Routing

Hello Guys I have a scenario where I would like to have your insights. 1. Client having Main site and DR site connected to same ISP with public IP line.2. The client has acquired a public IP block (/24) and would like to use same on both main and DR ...

Hi, Is there a Cisco documentation that can show comparison of each CE/Remote Site router model in attaining certain download and upload speed of a WAN connection(MPLS,broadband,etc). Thanks. 

Tunnel comes up and can see and access protected traffic but cannot access web (Split Tunnel). Don't know if access problem or route issue.Listed below is configuration for Cisco 871, any help very much appreciated. crypto isakmp policy 1 encr 3des a...

I installed a E1200 router in my in-law's home and the connection keeps dropping. When working there will several devices successfully connected some via wireless (some phones, ipad, laptops, Roku) and 1 desktop hardwired.Usually once or twice a day ...

Hi guys,I've a problem with a router 2811:Upgrade ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0xe36...

HelloI am fairly new to cisco gear.I am getting extremely slow internet speeds when I try using my router and switch.This is how I have it configured.Cable modem is plugged into Gi0/0 of router (1941)Switch (48Port 3560 PoE) is plugged into Gi0/1Gi0/...

Hi I am changing IOS of Cisco ASR 1001  from asr1001-universalk9.03.07.02.S.152-4.S2.binto asr1000rp1-adventerprisek9.03.04.02.S.151-3.S2.bin but everty time it boot up with old IOS universalk9. Is it becaused of Licence issue.Router#sh bootvarBOOT v...

Hi all, We use an infoblox device as our DHCP server, so in principle all MAC addresses are known on this server. If you want to do authentication based on MAC address, can you speak -one way or the other- with the Infoblox device?

We have 2 4500x switches with Ent Services licences.  The plan is to replace the current core routers with a L3 switched core using the 4500x with VSS.  The core will connect 3 building data closets, a local data center and 18 remote WAN sites.  Engi...

I have a 2811 with 512 of memory installed (two by 256).  The router has been sitting spare for sometime and I know there was once a memory problem with it long ago.  It has two 256M Non ECC DIMMs installed and seems to work fine.  I recently tried t...

in our org. we have two vpn link having 1 isp lan ip 10.190.x.x/24 and 2nd isp lan is 10.191.x.x/24.  2 internet link . 2 vpn is backup link . . now i have to restructure the networking due to shifting of link. currently if primay down. seconday link...

A Service Provider we are working with, tells us that BGP Community (transparency) is available, but BGP community (routing) is still under internal discussion.Do you know what is the difference between both? What is missing by not implementing BGP r...

Hello,I got a Nexus 7000 supervisor module recently, I met a SNMP problem for this moduleI would like to know which specific OIDs to use to monitor the following using SNMP on a Nexus 7000 supervisor module:- Port status- CPU total utilization- Power...

Hello,Please help me with this problem. Attached network diagram & router's configuration for ref.Requirement,To route the traffic from R1 to R3 via RSVP-Tunnel inside VRF "a"Issues:1.MP-BGP routes not being exchanged between the router's. However th...