Logging Message on Router

[Reza_Mohd]

Hi,

I would appreciate if I can get any help regarding stopping the logging message. I did run the command no logging console but even I'm keep getting the same.

Thank you.

Regard

Reza

[Georg Pauwen]

Hello,

try:

term no mon

[Reza_Mohd]

Dear Pauwen,

Thank you so much for quick response.

I tried mentioned command before, but still I'm getting the logging message.

Regards

Reza

[Georg Pauwen]

Hello,

Router(config)#no logging monitor

Otherwise post the full config of your router...

[Georg Pauwen]

Also, you might have some debugging turned on.

Router#u all

[Reza_Mohd]

Dear Pauwen,

Unfortunately, I won't be able to post the log now as office already closed.

Will surely send you the logs early morning.

Thank you so much sir.

Regards

Reza

[Deepak Kumar]

Hi,

Please share the output of "Show logging"

Regards,

Deepak Kumar

[Reza_Mohd]

Hi Deepak,

Here is the show logging:

Cisco4321#show logging
Syslog logging: disabled (0 messages dropped, 2 messages rate-limited, 132 flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.

No Inactive Message Discriminator.

Console logging: level debugging, 168 messages logged, xml disabled,
filtering disabled
Monitor logging: disabled
Buffer logging: level debugging, 36 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled

No active filter modules.

Trap logging: level debugging, 39 message lines logged
Logging Source-Interface: VRF Name:

Log Buffer (4096 bytes):

*Nov 3 07:28:32.590: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is initialized
*Nov 3 07:28:34.135: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = esg Next reboot level = ipbasek9 and License = ipbasek9
*Nov 3 07:28:35.318: %ISR_THROUGHPUT-6-LEVEL: Throughput level has been set to 50000 kbps
*Nov 3 07:28:36.443: %IOSXE_RP_NV-3-NV_ACCESS_FAIL: Initial read of NVRAM contents failed
*Nov 3 07:28:39.920: dev_pluggable_optics_selftest attribute table internally inconsistent @ 0x144

*Nov 3 07:28:43.603: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Nov 3 07:28:44.454: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Nov 3 07:28:44.454: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Nov 3 07:28:44.454: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Nov 3 07:28:44.462: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Nov 3 07:28:45.789: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Nov 3 07:28:45.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Nov 3 07:28:45.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up
*Nov 3 07:28:45.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up
*Nov 3 07:28:45.841: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Nov 3 07:28:45.841: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up
*Nov 3 07:28:47.109: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled
*Nov 3 07:28:47.114: %SPA_OIR-6-OFFLINECARD: SPA (ISR4321-2x1GE) offline in subslot 0/0
*Nov 3 07:28:47.119: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Nov 3 07:28:47.119: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Nov 3 07:28:47.120: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Nov 3 07:28:47.120: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Nov 3 07:28:47.154: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Nov 3 07:28:47.195: %SPA-3-ENVMON_NOT_MONITORED: SIP0: iomd: Environmental monitoring is not enabled for ISR4321-2x1GE[0/0]
*Nov 3 07:28:51.910: %SPA_OIR-6-ONLINECARD: SPA (ISR4321-2x1GE) online in subslot 0/0
*Nov 3 07:28:53.863: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed state to down
*Nov 3 07:28:53.904: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to down
*Nov 3 07:29:12.846: %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to administratively down
*Nov 3 07:29:12.846: %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to administratively down
*Nov 3 07:29:12.846: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down
*Nov 3 07:29:12.882: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
*Nov 3 07:29:16.277: %SYS-5-RESTART: System restarted --
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S4b, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Mon 17-Oct-16 20:23 by mcpre
*Nov 3 07:29:18.783: %SYS-6-BOOTTIME: Time taken to reboot after reload = 6007325 seconds
*Nov 3 07:30:09.444: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed state to down
*Nov 3 07:30:14.563: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to down
*Nov 3 07:36:49.401: %SYS-5-LOGGING_STOP: Logging disabled - CLI initiated

Cisco4321#

[Deepak Kumar]

Hi,

Type a command

"no logging console"

Regards,

Deepak Kumar

[Reza_Mohd]

Hi Deepak,

Still I'm getting the logging message:

Cisco4321(config)#no logging con
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 141.145.10.140(19995) -> 202.123.25.226(25), 1 packets
Cisco4321(config)#no logging console

%SYS-5-LOG_CONFIG_CHANGE: Console logging disabledFIU-Cisco4321(config)#
Cisco4321(config)#no logging console
Cisco4321(config)#
Cisco4321(config)#
Cisco4321(config)#do wr
Building configuration...

[OK]
Cisco4321(config)#exit
%
SYS-5-CONFIG_I: Configured from console by consoleFIU-Cisco4321#
Cisco4321#
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 40.107.2.47(33192) -> 202.123.25.226(25), 1 packet
Cisco4321#

[Deepak Kumar]

Hi,

How do you log in the device? Is it Telnet/SSH or Local Console?

Regards,

Deepak Kumar

[Reza_Mohd]

HI Deepak,

I'm login on the device through local console.

Regards

Reza

[Deepak Kumar]

Hi,

Please share an output"Show IP access-list"

It's looking like a bug in the IOS and also confirms the current ISO Version. 

Regards,

Deepak Kumar

[Deepak Kumar]

Hi,

As per shared logs, it looks like that you have configured one extended ACL"121" with the log or log-input keywords in the ACL.

Is it correct? If yes then please remove those keyboard from the end of ACL or update device. 

Regards,

Deepak Kumar

[Reza_Mohd]

Cisco4321#
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 40.107.2.47(33192) -> 202.123.25.226(25), 1 packet
Cisco4321#
Cisco4321#
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 81.12.78.250(12099) -> 202.123.25.226(80), 116 packets
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 206.229.236.45(31474) -> 202.123.25.226(25), 170 packets
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 40.107.5.85(30976) -> 202.123.25.226(25), 1 packet
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 157.150.240.17(62139) -> 202.123.25.226(25), 206 packets
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 40.107.7.83(61072) -> 202.123.25.226(25), 283 packets
Cisco4321#
%FMANFP-6-IPACCESSLOGP: SIP0: fman_fp_image: list 121 permitted tcp 40.107.6.47(26114) -> 202.123.25.226(25), 1 packet
Cisco4321#