08-01-2012 02:37 AM - edited 03-04-2019 05:08 PM
Hi,
we have two 6509 catalyst. we bought two new SFM-capable 16 port 1000mb GBIC/WS-X6516A-GBIC module. but our catalysts doesnt support them. we don't know the reason. we tried on another 6500 series catalyst they worked.
here are the outputs from our 6509:
Core-SW-1#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 1-subslot SPA Interface Processor-600 7600-SIP-600 JAE14090958
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1413DX2B
3 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414EL2Q
4 1 Application Control Engine Module ACE20-MOD-K9 SAD1408036Z
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1414ERDT
6 5 Supervisor Engine 720 10GE (RPR-Warm) VS-S720-10G SAL1414ERE3
7 16 CEF720 16 port 10GE WS-X6716-10GE SAL1414ER93
8 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1326SVBS
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 68ef.bd43.20c0 to 68ef.bd43.20ff 1.3 Unknown Unknown PwrDown
2 68ef.bd73.d3b0 to 68ef.bd73.d3df 3.4 12.2(18r)S1 12.2(33)SXI6 Ok
3 c47d.4f8f.ffe0 to c47d.4f8f.ffef 1.1 12.2(18r)S1 12.2(33)SXI6 Ok
4 0026.cb89.6b00 to 0026.cb89.6b07 2.6 8.7(0.22)ACE A2(1.6a) Ok
5 001e.4a7e.fb60 to 001e.4a7e.fb67 3.2 8.5(3) 12.2(33)SXI6 Ok
6 0026.cb61.13e0 to 0026.cb61.13e7 3.2 8.5(3) 12.2(33)SXI6 Ok
7 8843.e1d0.ab80 to 8843.e1d0.ab8f 1.1 12.2(18r)S1 12.2(33)SXI6 Ok
8 0026.0b7d.aec8 to 0026.0b7d.aed7 4.7 Unknown 12.2(33)SXI6 PwrDown
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 SIP Distributed Forwarding 7600-SIP-600-DC JAE14090967 1.1 PwrDown
2 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1414EFNQ 1.6 Ok
3 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1414EL5J 1.6 Ok
5 Policy Feature Card 3 VS-F6K-PFC3CXL SAL1414EFCT 1.2 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1414EW4T 2.1 Ok
6 Policy Feature Card 3 VS-F6K-PFC3CXL SAL1414EFEL 1.2 Ok
7 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1414EF3K 1.6 Ok
Mod Online Diag Status
---- -------------------
1 Not Applicable
2 Pass
3 Pass
4 Pass
5 Pass
6 Pass
7 Pass
8 Not Applicable
the module is in slot 8
Core-SW-1#sh power
system power redundancy mode = redundant
system power total = 5771.64 Watts (137.42 Amps @ 42V)
system power used = 2523.36 Watts (60.08 Amps @ 42V)
system power available = 3248.28 Watts (77.34 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 5771.64 137.42 OK OK on
2 WS-CAC-6000W 5771.64 137.42 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 210.00 5.00 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 7600-SIP-600 341.88 8.14 - - on off (DFC mismatch)
2 WS-X6748-GE-TX 392.70 9.35 392.70 9.35 on on
3 WS-X6716-10GE 487.20 11.60 487.20 11.60 on on
4 ACE20-MOD-K9 219.66 5.23 219.66 5.23 on on
5 VS-S720-10G 363.30 8.65 363.30 8.65 on on
6 VS-S720-10G 363.30 8.65 363.30 8.65 on on
7 WS-X6716-10GE 487.20 11.60 487.20 11.60 on on
8 WS-X6516A-GBIC 152.04 3.62 - - on off (not supported)
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 2523.36 Watts (60.08 Amps @ 42V)
system auxiliary power used = 0 Watt
Core-SW-1#sh module switch 1 slot 8
Switch Number: 1 Role: Virtual Switch Active
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
8 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1326SVBS
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
8 0026.0b7d.aec8 to 0026.0b7d.aed7 4.7 Unknown 12.2(33)SXI6 PwrDown
Mod Online Diag Status
---- -------------------
8 Not Applicable
can anybody help us with this problem?
08-01-2012 02:58 AM
Hi Zi,
Can you please tell me the superviser software version ????
If you are using module WS-X6516A-GBIC, you will see that "The WS-X6516A-GBIC version of this module is not supported in software release 6.x. The WS-X6516A-GBIC version is supported in software release 7.5(1)."
In this case, for Supervisor Engine 1 to support module WS-X6516A-GBIC, the supervisor needs to be upgraded to at least CatOS version 7.5(1).
Regards
please rate if it helps.
08-01-2012 03:45 AM
Hi Sandeep,
here is usperviser version : 12.2(33)SXI6
IOS version: s72033-advipservicesk9_wan-mz.122-33.SXI6.bin
System Bootstrap, Version 12.2(17r)SX6
08-01-2012 04:24 AM
HI Zo,
I think its the problem of software version.
WS-X6516A-GBIC | SUP 720 SUP 32 SUP 2 | 12.2(14)SX 12.2(18)SXF 12.2(17d)SXB |
Please check this ..and solve it.
Regards
Please rate if it helps.
08-01-2012 04:45 AM
Hi,
but ve have VS-S720-10G with 12.2(33)SXI6
i think this is newer version
can you explain in detail please ?
08-01-2012 05:07 AM
Hi Zi,
This documents will explain you everything:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/release/notes/hardware.html
Note•Not supported in virtual switch mode.
•Use with Release 12.2(33)SXH or later requires DFC ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6010.html
Regards
Please rate if it helps.
08-01-2012 08:49 PM
Hi,
one more question. will this sw version affect our other modules? if you see from my first message we have installed another modules, will they work?
08-01-2012 11:00 PM
HI Zi,
If all other modules are fit for the superviser and superviser engine have the minimum software version ....then all will work.
It is alwayas better to check the isoftware version of the Sup. engine before inserting the module.
As per your output:
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 7600-SIP-600 341.88 8.14 - - on off (DFC mismatch)
2 WS-X6748-GE-TX 392.70 9.35 392.70 9.35 on on
3 WS-X6716-10GE 487.20 11.60 487.20 11.60 on on
4 ACE20-MOD-K9 219.66 5.23 219.66 5.23 on on
5 VS-S720-10G 363.30 8.65 363.30 8.65 on on
6 VS-S720-10G 363.30 8.65 363.30 8.65 on on
7 WS-X6716-10GE 487.20 11.60 487.20 11.60 on on
8 WS-X6516A-GBIC 152.04 3.62 - - on off (not supported)
just check the slot 1 and 8 ..and check the ios version on the engine.
Hope this helps.
Regards
Please rate if it helps.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide