10-28-2006 04:45 AM - edited 03-03-2019 02:30 PM
Hello everybody, I have one problem and any advice would be great:
This is my situation:
Telecom operater have access lines for people who dial into my company to get to Internet. My company have 2 WIC-2T interfaces which are connected to telco. Something close as this:
TELCO Equipm. for dial in -----------link for traffic distribution--------------WIC2T(CISCO 2651XM)----Internet
note: there are two ports combined in multilink (4Mbps speed)
PROBLEM: When an user use only one B channel of an ISDN connection, Telco equipment connect user to my router and user is able to connect to Internet by us.
When user combine 2 B channels into multilink, there is no traffic at all from the user to the my company or Internet. I don't know what could be problem
This is the brief config of my Cisco 2651XM
aaa new-model
!
!
aaa authentication login default local
aaa authentication ppp default group radius
aaa authorization network default group radius
aaa accounting delay-start
aaa accounting network default start-stop group radius
!
aaa session-id common
clock timezone CET 1
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
vpdn enable
!
vpdn-group 1
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname cvxtunel
source-ip <!!!!!!!!REMOVED!!!!!!!>
l2tp tunnel password 0 <!!!!!!!!REMOVED!!!!!!!>
!
vpdn-group 2
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname tunelcvx
source-ip <!!!!!!REMOVED!!!!!!!!>
l2tp tunnel password 0 <!!!!!!!!REMOVED!!!!!!!>
!
!
!
username <!!!!!!!!REMOVED!!!!!!!> privilege 15 password 0 <!!!!!!!!REMOVED!!!!!!!>
username <!!!!!!!!REMOVED!!!!!!!> password 0 <!!!!!!!!REMOVED!!!!!!!>
!
!
interface Multilink1
ip address <!!!!!!!!REMOVED!!!!!!!> 255.255.255.252
ppp multilink
ppp multilink group 1
!
interface FastEthernet0/0
ip address <!!!!!!!!REMOVED!!!!!!!> 255.255.255.248
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/1
no ip address
shutdown
!
interface Serial0/2
bandwidth 2048
no ip address
encapsulation ppp
no fair-queue
ppp multilink
ppp multilink group 1
!
interface Serial0/3
bandwidth 2048
no ip address
encapsulation ppp
no fair-queue
ppp multilink
ppp multilink group 1
!
interface Virtual-Template1
ip unnumbered FastEthernet0/0
no logging event link-status
peer default ip address pool default
no keepalive
ppp authentication pap chap
ppp ipcp dns <!!!!!!!!REMOVED!!!!!!!> <!!!!!!!!REMOVED!!!!!!!>
ppp multilink
!
ip local pool default <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
ip route <!!!!!!!!REMOVED!!!!!!!>
!
!
no ip http server
no ip http secure-server
!
snmp-server community <!!!!!!!!REMOVED!!!!!!!>
snmp-server contact <!!!!!!!!REMOVED!!!!!!!>
!
!
radius-server attribute 8 include-in-access-req
radius-server host <!!!!!!!!REMOVED!!!!!!!> auth-port 1812 acct-port 1813 key <!!!!!!!!REMOVED!!!!!!!>
radius-server retransmit 0
!
control-plane
!
!
!
10-29-2006 10:46 AM
Same question again:)
Is anyone have any advice? If something from this explanation is missing, please feel free to post the additional questions.
Thanks again,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide