04-06-2012 10:24 PM - edited 03-04-2019 03:56 PM
Hi All,
My Router is showing like this can any one explain me what it is and why its showing like this
and every time its going to Rmon mode some times going to Normal mode
how to tourble shoot this problem,
is the problem is flash or some thing els explain me and why its showing like this (Readonly ROMMON initialized)
The output is shown like this
System Bootstrap, Version 12.4(11r)XW3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2007 by cisco Systems, Inc.
C1860 series platform with 262144 Kbytes of main memory
Readonly ROMMON initialized
program load complete, entry point: 0x80015000, size: 0xb700
program load complete, entry point: 0x80015000, size: 0xb700
program load complete, entry point: 0x80020000, size: 0x1dac7e0
Self decompressing the image : ################################################################################################################################################################################################################################################ [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
Bad FIO_0 EC220 vendor device id 0xFFFFFFFF
0X00003960 Onboard Ethernet
0X000F3BB0 public buffer pools
0X00703000 public particle pools
TOTAL: 0X007FA510
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 7Mb.
adjusted iome size up to minimum size of: 0X00C00000
Using 4 percent iomem. [12Mb/256Mb]
Bad FIO_0 EC220 vendor device id 0xFFFFFFFF
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1861 Software (C1861-SPSERVICESK9-M), Version 12.4(11)XW6, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 13-Feb-08 16:03 by prod_rel_team
Image text-base: 0x800200EC, data-base: 0x82C7C574
04:34:37 UTC Sat Apr 7 2012: Unexpected exception to CPU: vector 200, PC = 0x80444C24, LR = 0x80444C08
-Traceback= 0x80444C24 0x80444C08 0x80439DA0 0x80437BE0 0x800379F8 0x825B289C 0x810F8858 0x810F8B4C 0x80227A6C 0x8022A36C
CPU Register Context:
MSR = 0x00049030 CR = 0x22008084 CTR = 0x00000000 XER = 0x20000000
R0 = 0x00000000 R1 = 0x84CAE0C0 R2 = 0xFFF5FFF5 R3 = 0x00001388
R4 = 0x00000000 R5 = 0x84FAE234 R6 = 0x00000F9F R7 = 0x001312D0
R8 = 0x431BDE83 R9 = 0x70020004 R10 = 0x211100BD R11 = 0x00000000
R12 = 0x84FAD030 R13 = 0xFFF5696C R14 = 0x810F8AEC R15 = 0x00000000
R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000
R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x84CAE121
R24 = 0x84410830 R25 = 0x84CAE120 R26 = 0x00000000 R27 = 0x84CAE121
R28 = 0x00000000 R29 = 0x0000F800 R30 = 0x0000001F R31 = 0x84FA8030
Writing crashinfo to flash:crashinfo_20120407-043437
=== Flushing messages (04:34:37 UTC Sat Apr 7 2012) ===
Queued messages:
No warm reboot Storage
*** System received a Bus Error exception ***
signal= 0xa, code= 0x200, context= 0x84636be0
PC = 0x80444c24, Vector = 0x200, SP = 0x84cae0c0
rommon 1 >
04-06-2012 10:54 PM
If you have any modules or WIC cards installed, remove them from the router and try again.
If the problem persists without the NM modules or WIC cards then try a different IOS version. Hopefully NOT the "XW" train.
04-06-2012 11:40 PM
there is no WIC CARD installed on this router what should i do for this router help to trouble shoot this problem
04-07-2012 02:44 AM
Already replied in another thread:
https://supportforums.cisco.com/message/3603500
Please do not open duplicates.
04-18-2012 04:56 AM
The exception vector in this output is 200. If this happens repeatedly then I would look at replacing the chassis.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide