Dear Experts,
I have recently configured a router 2800 series for 2Mbps of Internet connections. E1 is directly terminated on the 2800
There are approx 20 + users on a remote site.
I am trying to configure a PAT so that all the lan users can access the internet.
Currently I have configured a NAT POOL and it is a one to one nat.
below is my config.
My question is how can I configure a PAT so that only one ip address will be used instead of assigning a pool.
Because if the users increase on site the POOL will be exausted.
I tried source list # ip nat inside source list 101 interface serial 0/1/0:0 overload however it does not work and none of the users are able to access internet.
when I run the command sh ip int brief I can see FA0/0 protocol is down can any one please help me weather the config is correct.
Test#sh ip int brief
Interface IP-Address OK? Method Status Prot
ocol
FastEthernet0/0 X.X.X.33 YES NVRAM up down
FastEthernet0/1 192.168.96.1 YES NVRAM up up
Serial0/0/0 unassigned YES NVRAM down down
Serial0/0/1 unassigned YES NVRAM administratively down down
Serial0/1/0:0 X.X.X.33 YES TFTP up up
Config_____________________
Current configuration : 1869 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname test
!
boot-start-marker
boot-end-marker
!
no logging buffered
!
no aaa new-model
!
resource policy
!
no network-clock-participate wic 1
ip subnet-zero
!
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.96.1 192.168.96.14
!
ip dhcp pool test
network 192.168.96.0 255.255.255.0
domain-name test.com
default-router 192.168.96.1
dns-server X.X.X.X
lease 8
!
!
ip name-server X.x.x.x
ip name-server X.X.X.X
no ftp-server write-enable
!
username XXXXXX privilege 15 secret 5 $1$9rpI$NoasdfsdfsaJy58SMEXP1
!
!
controller E1 0/1/0
framing NO-CRC4
clock source internal
channel-group 0 timeslots 1-31
!
!
interface FastEthernet0/0
description $ETH-WAN$
ip address x.x.x.33 255.255.255.240
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.96.1 255.255.255.0
ip nat inside
duplex auto
speed auto
!
interface Serial0/0/0
no ip address
clockrate 2000000
!
interface Serial0/0/1
no ip address
shutdown
clockrate 2000000
!
interface Serial0/1/0:0
ip unnumbered FastEthernet0/0
ip nat outside
!
interface BRI1/0
no ip address
shutdown
!
interface BRI1/1
no ip address
shutdown
!
interface BRI1/2
no ip address
shutdown
!
interface BRI1/3
no ip address
shutdown
!
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/1/0:0
!
ip http server
ip nat pool test-Nat-Pool x.x.x.34 x.x.x.44 netmask 255.255.255.240
ip nat inside source list 1 pool test-Nat-Pool
!
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.96.0 0.0.0.255
access-list 101 remark SDM_ACL Category=16
access-list 101 permit ip any any
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login local
!
scheduler allocate 20000 1000
!
end
