Routing

Hi All,I have a bit of a problem and was hoping someone might be able to help me out.Basically I am trying to do a bit of a clean up at work and replacing  two dlink (home style) ADSL modems with a single Cisco 2901 router with  2 ADSL HWICs. On top ...

Hello!I want to configure multilink between two Cisco 7206 routers POS interfacesafter configuring both sides**********************************Router 1interface Multilink5 ip address 172.16.0.1 255.255.255.252 ppp multilink ppp multilink group 5inter...

HiI am facing problems when using a static public IP block while connecting to internet.. The browser takes time to load pages .Sometimes I have to keep on hitting the refresh button to get the page loaded..I have formatted my computer but was of no ...

HiWe have two 6509 switch with IOS s72033-advipservicesk9_wan-mz.122-18.SXF9Out of this two, one switch is showing high CPU utlization(more than 90%). Another switch shows 30-35% CPU utilization. Both switch has same Hardware as well as software.Pls....

Hi Guys,I have a Cisco 881 and 877, with branch offices that have their own 877.Each branch router has a DVTI to the head offices 881 and 877, with the Tunnel going to the 881 being 4000kbps and the 877 being 800kbps. Using EIGRP to share the routes ...

Hello,     It seems to me I am receiving OSPF hello packets, but I am unable to ping some devices, one log example below:Jan 16 05:15:13: OSPF: Rcv hello from 10.82.x.x area 192.168.x.x from Vlan400 192.168.x.x     I have two vlans that had been oper...

I am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR. If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1? ...

DearsHiI will be subscribe in ISDN PRI(E1)(32 Channels)(Dial Out) in the HQ and ISDN IN the branches(Dial In) (now i have 9 branches) one branches cannot be connected vi ISDN So I have wasted Bandwidth , can i use it to do internet access ?I hear sou...

HI.I have this sytuaction.LAN_A-->WRVS4400n-->WAG160N--->INTERNET<---WAG54GS<--WRVS4400n<--LAN_BI want make VPN between WRVS4400n.LAN_ALAN_BWRVS4400n: Lan 192.168.10.11 WAN 192.168.9.11WAG160N: Lan 192.168.9.10  WAN static IP xx.xx.xx.81WRVS4400n: La...

Hello,I am using a linksys WRT120N router as a __Access point__ in my student dorm (according to the rules!). As long as i used it as a router, I never had problems with the speed. But now, the connection is very slow.For example, when I am wirelessl...

Hello   What are the features that are not supported by CEF ?In this case are they dropped or punted to next switching level ?Also when do packets will be dropped If punted to next switching level ?In below command, why do "Encap_fail" & "Unsupported...

Dear.our DR backbone has been enabled ospf and ripv2 at same routing table. ospf is main circuit for exchange routing with HQ router.and RIP is for backup routing which is connected MPLS low speed circuit.we are going to enable RIPv2 on DR backbone r...

DearsI am facing problem with FWSM. It is using version 3.2. I have 2 caore switches and each one have one FWSM. Core switches and FWSM are working in ACTIVE/STANDBY mode. If I am trying to do session from secondary switch it can only go to the Activ...