Netflow on ASR 920 issue

[marcio.tormente]

Hello Folks!

I'm replacing my router from ISR 4431 to ASR 920 and the

netflow

is not working, actually there are other commands as well.

Netflow

when I try to apply the config into the interface shows the following msg:

RT01(config-if)# ip flow monitor FLOWin input
% Flow Monitor: Failed to add monitor to interface: Unsupported template

I saw documentation that I should change my license to "metroaggrservices", but this license is not available.

I'm running the image: asr920-universalk9_npe.16.09.03.SPA.bin

Is there any other way to enable the

Netflow

The command below are not supported as well, do you know the alternative?

platform qfp utilization monitor load 80
platform hardware throughput level 1000000

Thanks

[balaji.bandi · Accepted solution]

what kind of license you have : 

check below thread :

https://community.cisco.com/t5/network-management/flexible-netflow-asr920-trouble/td-p/3767918

[marcio.tormente]

Hello,

I saw this documentation that you mentioned, but I did this process and didn´t work".

BR238-INT-RTR02#sh license
Index 1 Feature: advancedmetroipaccess
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Index 2 Feature: metroipaccess
Period left: Not Activated
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 3 Feature: metroaccess
Period left: Not Activated
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 4 Feature: 1588
Index 5 Feature: 1GEupgradelicense
Index 6 Feature: 10GEupgradelicense
Index 7 Feature: 12portGE-2port10GE
Period left: Life time

[balaji.bandi]

RT01(config-if)# ip flow monitor FLOWin input
% Flow Monitor: Failed to add monitor to interface: Unsupported template

Can you post

Netflow

related all the config and what interface you trying to configure?

here is the sample config :

low record TEST_IPV4_RECORD
 match ipv4 source address
 match ipv4 destination address
 match ipv4 protocol
 match transport source-port
 match transport destination-port
 collect counter packets
 collect counter bytes
!
!
flow exporter TEST_EXPORTER
 destination 192.168.100.1
 source Loopback1
 transport udp 9999
!
!
flow monitor TEST_IPV4_MONITOR
 exporter TEST_EXPORTER
 cache timeout inactive 20
 cache timeout active 180
 record TEST_IPV4_RECORD
!
interface GigabitEthernet0/1/0
 ip address 10.10.10.2 255.255.255.0
 ip flow monitor TEST_IPV4_MONITOR input
 speed 1000
 no negotiation auto
!

check the SDM prefer template :

https://www.cisco.com/c/en/us/td/docs/routers/asr903/software/guide/chassis/xe-3s/b_Config_Guide_fullbook/b-cfg-sdm.html#reference_0418A0A6C8864FF0B19B28658F595431

[Georg Pauwen]

Hello,

what is the exact 920 model you have ? According to the documentation linked below, the following applies:

--> For Cisco ASR-920-12CZ-A, ASR-920-12CZ-D, ASR-920-4SZ-A, ASR-920-4SZ-D, and ASR-920-12SZ-IM routers—sdm prefer netflow-video.

--> RSP2 and Cisco ASR-920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M routers—sdm prefer video.

https://www.cisco.com/c/en/us/td/docs/routers/asr920/configuration/guide/netmgmt/fnf-xe-3e-asr920-book.html

[marcio.tormente]

Hello Georg!

It is working now, for some reason I had to apply the command

sdm prefer netflow-video

2x, and only in the second time that worked.

I appreciate you and Balaji.Bandi for supports me.