Hi ,
i have problem connecting Cisco 867VAE this is my config and my diagnostic file ( IOS version ==> c860vae-ipbasek9-mz.151-4.M4.bin )
-----------------------------------------------------------
diag file :
sBelfort#sh atm int atm0
Interface ATM0:
AAL enabled: AAL5,, Maximum VCs: 2, Current VCCs: 0
VCIs per VPI: 1024,
Max. Datagram Size: 2096
PLIM Type: ADSL - 4608Kbps Upstream, DMT, TX clocking: LINE
0 input, 0 output, 0 IN fast, 0 OUT fast
Avail bw = 4608
Config. is ACTIVE
sBelfort#sh ip int brief
Interface IP-Address OK? Method Status Prot ocol
ATM0 unassigned YES NVRAM down down
ATM0.1 unassigned YES unset down down
Dialer0 unassigned YES NVRAM up up
Ethernet0 unassigned YES NVRAM administratively down down
FastEthernet0 unassigned YES unset down down
FastEthernet1 unassigned YES unset down down
FastEthernet2 unassigned YES unset up up
FastEthernet3 unassigned YES unset up up
GigabitEthernet0 unassigned YES NVRAM administratively down down
NVI0 unassigned YES unset administratively down down
Vlan1 192.168.1.1 YES NVRAM up up
sBelfort#show atm vc
Codes: DN - DOWN, IN - INACTIVE
VCD / Peak Av/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells St
0.1 1 8 35 PVC SNAP UBR 0 IN
sBelfort#sh inter atm0.1
ATM0.1 is down, line protocol is down
Hardware is BCM6300 ATMSAR, address is 70ca.9bbd.f0b7 (bia 70ca.9bbd.f0b7)
MTU 2038 bytes, BW 4608 Kbit/sec, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
Keepalive not supported
0 packets input, 0 bytes
0 packets output, 0 bytes
0 OAM cells input, 0 OAM cells output
AAL5 CRC errors : 0
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 0
Last clearing of "show interface" counters never
sBelfort#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: NA
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xA19B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' 'BDCM'
Modem Vendor Specific: 0x4602 0xA19B
Modem Vendor Country: 0xB500 0xB500
Serial Number Near: GMK1148001K 867VAE 15.1(4)M
Serial Number Far:
Modem Version Near: 15.1(4)M
Modem Version Far: 0xA19B
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
Line Attenuation: 0.0 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 14.1 dB 7.6 dB
Attainable Rate: 41364 kbits/s 1997 kbits/s
Actual Power: 14.5 dBm 4.8 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 21.9 55.9 N/A N/A 51.5 59.1 N/A
Signal Attenuation(dB): 21.9 55.9 N/A N/A 50.9 N/A N/A
Noise Margin(dB): 14.0 14.3 N/A N/A 7.6 N/A N/A
Total FECS: 54445 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 24 24
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
Bit swap: 0 1
Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded N/A (0)
Modem FW Version: 23i
Modem PHY Version: A2pv6C032b.d23i
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 21399 0 1017
Previous Speed: 0 0 0 0
Reed-Solomon EC: 0 54445 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 19.00 0.00 0.00
Actual INP: 0.00 8.01 0.00 0.00
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
debug atm errors
debug pppatm errors
debug pppatm events
debug ppp neg
debug ppp auth
debug ppp err
*Apr 4 14:33:42.887: (atm_vc_is_bridged_dot1q)ATM: VC with handle 0x0 not found
*Apr 4 14:33:42.887: VC micro block get: Invalid vc handle
*Apr 4 14:33:42.887: VC micro block get: Invalid vc handle
*Apr 4 14:33:44.935: (atm_vc_is_bridged_dot1q)ATM: VC with handle 0x0 not found
*Apr 4 14:33:44.935: VC micro block get: Invalid vc handle
*Apr 4 14:33:44.935: VC micro block get: Invalid vc handle
*Apr 4 14:33:46.983: (atm_vc_is_bridged_dot1q)ATM: VC with handle 0x0 not found
can anyone help me please
