Protocol status is showing as down on C1861E-SRST-F/K9 router

[sharath.babu9022@gmail.com]

Hi All,

Need your help to resolve an issue with my C1861E-SRST-F/K9 model router. Few interfaces of my router is showing protocol as down but line status is up.

amusorf-wanrtr01#sh ip int br
Interface IP-Address OK? Method Status Protocol
Async1 unassigned YES unset administratively down down
FastEthernet0/0 x.x.x.x YES DHCP up up
FastEthernet0/1/0 unassigned YES unset up down
FastEthernet0/1/1 unassigned YES unset up up
FastEthernet0/1/2 unassigned YES unset up up
FastEthernet0/1/3 unassigned YES unset up up
FastEthernet0/1/4 unassigned YES unset up down
FastEthernet0/1/5 unassigned YES unset up down
FastEthernet0/1/6 unassigned YES unset up down
FastEthernet0/1/7 unassigned YES unset up down
FastEthernet0/1/8 unassigned YES unset up down
Vlan1 unassigned YES unset administratively down down
Vlan27 x.x.x.x YES NVRAM up up
Vlan600 x.x.x.x YES NVRAM up up
Loopback0 x.x.x.x YES NVRAM up up
Tunnel10 x.x.x.x YES NVRAM up up

Non working ports

amusorf-wanrtr01#sh int FastEthernet0/1/0 switchport
Name: Fa0/1/0
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: down
Administrative Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 27 (VLAN0027)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: none
Protected: false
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: 600
Appliance trust: none

amusorf-wanrtr01#sh int FastEthernet0/1/5 switchport
Name: Fa0/1/5
Switchport: Enabled
Administrative Mode: dynamic access
Operational Mode: down
Administrative Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 27 (VLAN0027)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: none
Protected: false
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: 600
Appliance trust: none

Working port

amusorf-wanrtr01#sh int FastEthernet0/1/1 switchport
Name: Fa0/1/1
Switchport: Enabled
Administrative Mode: dynamic access
Operational Mode: dynamic access
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: native
Negotiation of Trunking: Disabled
Access Mode VLAN: 27 (VLAN0027)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 27,600
Protected: false
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: 600
Appliance trust: none

Running configuration of non working ports

amusorf-wanrtr01#sh run int FastEthernet0/1/0
Building configuration...

Current configuration : 202 bytes
!
interface FastEthernet0/1/0
description HP Officejet Pro 8600 Premium
switchport access vlan 27
switchport voice vlan 600
no ip address
macro description cisco-phone
spanning-tree portfast
end

amusorf-wanrtr01#sh run int FastEthernet0/1/5
Building configuration...

Current configuration : 192 bytes
!
interface FastEthernet0/1/5
description IP Phone/Desktop PC
switchport access vlan 27
switchport voice vlan 600
no ip address
macro description cisco-phone
spanning-tree portfast
end

Running config of working port

amusorf-wanrtr01#sh run int FastEthernet0/1/1
Building configuration...

Current configuration : 192 bytes
!
interface FastEthernet0/1/1
description IP Phone/Desktop PC
switchport access vlan 27
switchport voice vlan 600
no ip address
macro description cisco-phone
spanning-tree portfast
end

Could you please help? I have bounced the interface but no luck.

c1861-advipservicesk9-mz.151-4.M5.bin is the version of the Code.

I need to connect a Meraki access point to this router.

[Giuseppe Larosa]

Hello,

>> I need to connect a Meraki access point to this router.

For this you will likely need to buy the power injector for the Meraki AP because it may require a POE+ device that is more then 15 W per port.

I cannot find specific info about your model C1861E.

For the cisco IP phone, do you have a power injector or you trying to use POE on the router port ?

For the non working ports try to use different LAN cables that you know they work for sure and repeat your tests.

If you have unused ports you can try to use them.

For the IP phone verify it is powered on either by POE or by an external power supply or by  a power injector.

Edit:

I have found only the following web page the datasheet links provide a link for the C1841 not for the C1861E.

https://www.cisco.com/c/en/us/support/routers/1861e-integrated-services-router-isr/model.html?dtid=osscdc000283

From the router picture we can understand it has an on board etherswitch module with 8 ports. But I am not able to find info about POE capabilities (if any).

Edit2:

this router is not mentioned / listed also on the migration document to newer ISR routers like from 1841 to C1941.

I think this router model has been designed for service providers to be the cheapest CPE with SRST for IP telephony. The eight LAN ports are there to avoid to install a separate LAN switch on small branch offices.

The C1841 has no VOIP features according the quick start guide:

https://www.cisco.com/c/en/us/td/docs/routers/access/1800/1841/hardware/quick/guide/1800qsg.html

The C1861E should qualify as a 1800 series modular router but when looking for links about modular 1800 routers only documents for the C1841 are provided.

Hope to help

Giuseppe

[Richard Burts]

I am not familiar with this 1861E, I expected some type of IOS router but the configuration shown seems to be more like a switch. Perhaps the output of show interface status might shed some light on this?

HTH

Rick

[sharath.babu9022@gmail.com]

Hi Rick,

Here is the output.

FastEthernet0/0 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is c08c.600c.2d40 (bia c08c.600c.2d40)
Description: DSL Connection
Internet address is 70.169.26.63/25
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 45
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 9000 bits/sec, 14 packets/sec
5 minute output rate 4000 bits/sec, 3 packets/sec
38074817 packets input, 1615209400 bytes
Received 20947376 broadcasts (0 IP multicasts)
2 runts, 0 giants, 0 throttles
367 input errors, 0 CRC, 0 frame, 5 overrun, 362 ignored
0 watchdog
0 input packets with dribble condition detected
11749208 packets output, 4181460655 bytes, 5 underruns
5 output errors, 0 collisions, 6 interface resets
90998 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
20 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/0 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d42 (bia c08c.600c.2d42)
Description: HP Officejet Pro 8600 Premium
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/1 is up, line protocol is up
Hardware is Fast Ethernet, address is c08c.600c.2d43 (bia c08c.600c.2d43)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:33, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6209769 packets input, 1828607033 bytes, 0 no buffer
Received 499711 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
11190012 packets output, 2591288789 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
2 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/2 is up, line protocol is up
Hardware is Fast Ethernet, address is c08c.600c.2d44 (bia c08c.600c.2d44)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:31, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2000 bits/sec, 2 packets/sec
5 minute output rate 3000 bits/sec, 3 packets/sec
4503994 packets input, 1304152049 bytes, 0 no buffer
Received 25627 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
1 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
9128243 packets output, 152006287 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
38 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/3 is up, line protocol is up
Hardware is Fast Ethernet, address is c08c.600c.2d45 (bia c08c.600c.2d45)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
696477 packets input, 107438471 bytes, 0 no buffer
Received 5905 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
4139346 packets output, 1392957928 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
2 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/4 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d46 (bia c08c.600c.2d46)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/5 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d47 (bia c08c.600c.2d47)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/6 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d48 (bia c08c.600c.2d48)
Description: IP Phone/Desktop PC
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/7 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d49 (bia c08c.600c.2d49)
Description: to amusorf_AP01
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1/8 is up, line protocol is down
Hardware is Fast Ethernet, address is c08c.600c.2d4a (bia c08c.600c.2d4a)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out

Fa0/1/0, Fa0/1/4 through Fa0/1/8 are the interfaces with which we are facing issues. Couple of IP phones are connected to this router and they are working perfectly fine.

amusorf-wanrtr01#sh int des
Interface Status Protocol Description
As1 admin down down
Fa0/0 up up DSL Connection
Fa0/1/0 up down HP Officejet Pro 8600 Premium
Fa0/1/1 up up IP Phone/Desktop PC
Fa0/1/2 up up IP Phone/Desktop PC
Fa0/1/3 up up IP Phone/Desktop PC
Fa0/1/4 up down IP Phone/Desktop PC
Fa0/1/5 up down IP Phone/Desktop PC
Fa0/1/6 up down IP Phone/Desktop PC
Fa0/1/7 up down to amusorf_AP01
Fa0/1/8 up down

amusorf-wanrtr01#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID Local Intrfce Holdtme Capability Platform Port ID
SEP20BBC0DD9DC8 Fas 0/1/1 139 H M IP Phone Port 1
SEP00B0E1EFE1B2 Fas 0/1/2 140 H M IP Phone Port 1

POE status.

amusorf-wanrtr01#sh power inline
PowerSupply SlotNum. Maximum Allocated Status
----------- -------- ------- --------- ------
INT-PS 0 88.000 15.791 PS GOOD
Interface Config Device Powered PowerAllocated
--------- ------ ------ ------- --------------
Fa0/1/0 auto Unknown Off 0.000 Watts
Fa0/1/1 auto IEEE-2 On 6.000 Watts
Fa0/1/2 auto IEEE-3 On 9.791 Watts
Fa0/1/3 auto Unknown Off 0.000 Watts
Fa0/1/4 auto Unknown Off 0.000 Watts
Fa0/1/5 auto Unknown Off 0.000 Watts
Fa0/1/6 auto Unknown Off 0.000 Watts
Fa0/1/7 auto Unknown Off 0.000 Watts

[sharath.babu9022@gmail.com]

We are not using any power injectors. Currently, couple of IP phones are connected to the router and they are working fine.

amusorf-wanrtr01#sh power inline
PowerSupply SlotNum. Maximum Allocated Status
----------- -------- ------- --------- ------
INT-PS 0 88.000 15.791 PS GOOD
Interface Config Device Powered PowerAllocated
--------- ------ ------ ------- --------------
Fa0/1/0 auto Unknown Off 0.000 Watts
Fa0/1/1 auto IEEE-2 On 6.000 Watts
Fa0/1/2 auto IEEE-3 On 9.791 Watts
Fa0/1/3 auto Unknown Off 0.000 Watts
Fa0/1/4 auto Unknown Off 0.000 Watts
Fa0/1/5 auto Unknown Off 0.000 Watts
Fa0/1/6 auto Unknown Off 0.000 Watts
Fa0/1/7 auto Unknown Off 0.000 Watts
amusorf-wanrtr01#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID Local Intrfce Holdtme Capability Platform Port ID
SEP20BBC0DD9DC8 Fas 0/1/1 160 H M IP Phone Port 1
SEP00B0E1EFE1B2 Fas 0/1/2 163 H M IP Phone Port 1

[Giuseppe Larosa]

Hello Sharath,

yes your router supports POE and should be fine for current POE devices like IP Phones.

However, the new Meraki AP may require more then 15 W in a single port and in that case your device may be not able to provide it if it supports the first generation standard of POE.

This is the only point of attention.

Have you been able to change the LAN cables on the not working ports ? or to try to use different ports ?

Hope to help

Giuseppe

[sharath.babu9022@gmail.com · Accepted solution]

Yes,  it is working now. I connected Meraki to all ports of the router hoping at least one would and I got lucky.

amusorf-wanrtr01#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID Local Intrfce Holdtme Capability Platform Port ID
SEP20BBC0DD9DC8 Fas 0/1/1 176 H M IP Phone Port 1
SEP00B0E1EFE1B2 Fas 0/1/2 174 H M IP Phone Port 1
e0cbbc512cf6 Fas 0/1/0 166 R S Meraki MR Port 0
amusorf-wanrtr01#sh power inline
PowerSupply SlotNum. Maximum Allocated Status
----------- -------- ------- --------- ------
INT-PS 0 88.000 31.191 PS GOOD
Interface Config Device Powered PowerAllocated
--------- ------ ------ ------- --------------
Fa0/1/0 auto IEEE-4 On 15.400 Watts
Fa0/1/1 auto IEEE-2 On 6.000 Watts
Fa0/1/2 auto IEEE-3 On 9.791 Watts
Fa0/1/3 auto Unknown Off 0.000 Watts
Fa0/1/4 auto Unknown Off 0.000 Watts
Fa0/1/5 auto Unknown Off 0.000 Watts
Fa0/1/6 auto Unknown Off 0.000 Watts
Fa0/1/7 auto Unknown Off 0.000 Watts