Hi,
The physical Gigabit interface in this router has bandwidth command set & the show interface command output reflects the same
But how does the Subinterface get its bandwidth set to 100 Mbps? I always thought subinterfaces inherit the physical interface bandwidth. isnt it?
Router#sh int GigabitEthernet0/0
GigabitEthernet0/0 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 64ae.0c98.ba10 (bia 64ae.0c98.ba10)
Description: link to PE
MTU 1500 bytes, BW 10000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 4/255, rxload 33/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 111823
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1323000 bits/sec, 142 packets/sec
5 minute output rate 177000 bits/sec, 96 packets/sec
3331038420 packets input, 405011219 bytes, 0 no buffer
Received 11024 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
2480626113 packets output, 2746510267 bytes, 0 underruns
1 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Router#sh run int GigabitEthernet0/0
Building configuration...
Current configuration : 186 bytes
!
interface GigabitEthernet0/0
description link to PE
bandwidth 10000
no ip address
ip flow ingress
ip route-cache flow
duplex full
speed 100
media-type rj45
no cdp enable
end
Router#sh int GigabitEthernet0/0.2015
GigabitEthernet0/0.2015 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 64ae.0c98.ba10 (bia 64ae.0c98.ba10)
Internet address is x.x.x.x/30
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 4/255, rxload 32/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2015.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
Router#sh run int GigabitEthernet0/0.2015
Building configuration...
Current configuration : 174 bytes
!
interface GigabitEthernet0/0.2015
encapsulation dot1Q 2015
ip address x.x.x.x 255.255.255.252
no cdp enable
service-policy output SE_SNAP_Q9000K_1M-0-7M-0_25
end
