cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
308
Views
9
Helpful
3
Replies
Highlighted
Enthusiast

Traceback on 7206 NPE-G1 router

Dear Experts ,

I'm getting below error on 7206VXR (NPE-G1)  with IOS "c7200-js-mz.124-3i.bin".. Any Clues

Mar 10 08:16:10.082: %SYS-2-BADBUFFER: Attempt to use contiguous buffer as scattered src, ptr= 662F04A4, pool= 64CCDCCC

-Process= "<interrupt level>", ipl= 1

-Traceback= 0x606E3654 0x60941328 0x60147294 0x6014B5CC

Mar 10 08:16:39.534: %ALIGN-3-SPURIOUS: Spurious memory access made at 0x60145708  reading 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x60145708 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x6183B528 0x60146060 0x6014B5CC 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x6183B828 0x60146060 0x6014B5CC 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x6183B88C 0x60146060 0x6014B5CC 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x601468D0 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x601468D4 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x6014690C 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x60146910 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x60146B58 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x60146B5C 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x60146D88 0x6014B5CC 0x0 0x0 0x0 0x0 0x0 0x0

Mar 10 08:16:39.534: %ALIGN-3-TRACE: -Traceback= 0x6182BE88 0x60146EE8 0x6014B5CC 0x0 0x0 0x0 0x0 0x0

3 REPLIES 3
Highlighted
Hall of Fame Community Legend

WOOOOOOOOOOOOOOOW!

That's a pretty old IOS.  I'd start thinking about upgrading your IOS.

Highlighted
VIP Expert

Disclaimer


The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

Tracebacks usually are indicative of some IOS software bug.  Often resolved after upgrading your IOS.

Highlighted
Cisco Employee

Hello Haris ,

I have decoded the traceback and see you are running into feature limitation . it is advised to upgrade your IOS and as well in certain cases , it is recommended to upgrade to NPE-G2 as well .

So I would suggest you to upgrade IOS and upgrade to NPE-G2. Hope this helps.

c7200-js-mz.124-3i.symbols.gz read in

Enter hex value: 0x606E3654 0x60941328 0x60147294 0x6014B5CC

0x606E3654:errmsg(0x606e3634)+0x20

0x60941328:c7100_dma_pak_coalesce(0x609412bc)+0x6c

0x60147294:fx1000_rx_interrupt(0x60142474)+0x4e20

0x6014B5CC:fx1000_check_tx(0x6014b5cc)+0x0

Enter hex value:  0x6183B528 0x60146060 0x6014B5CC 0x0 0x0 0x0 0x0 0x0

0x6183B528:cef_preprocess_vlan_pkt(0x6183b4d4)+0x54

0x60146060:fx1000_rx_interrupt(0x60142474)+0x3bec

0x6014B5CC:fx1000_check_tx(0x6014b5cc)+0x0

0x0:__start(0x60008000)+-0x60008000

0x0:__start(0x60008000)+-0x60008000

0x0:__start(0x60008000)+-0x60008000

0x0:__start(0x60008000)+-0x60008000

0x0:__start(0x60008000)+-0x60008000

- Sruthi.