10-21-2018 05:31 AM - edited 03-05-2019 10:59 AM
Hi to all,
A PC (Windows10) ihas 10Gb NIC connected to 10Gb interface on 2960X Switch (via SFP+).
2960X is connected to another 10Gbe switch (Quanta 10Gbe) via SFP+
A Nas is connected to Quanta switch via SFP+
Result is : PC < SFP+ > 2960X < SFP+ > QUANTA < SFP+ > NAS
All the chain is 10Gbe connected with SFP+
When i try to transfert files (NetBIOS transfert), I'm not be able to do more than 1Gb transfert rate (120Mo/s)
At the begining i start at 600Mo/s but some few second after it go down quickly to 120Mo/s...
It seems that the Cisco device is reducing the transfert rate...
How can i change this state ?
Best Regards.
10-21-2018 06:42 AM
Hello,
post the config of the 2960 as well as the output of 'sh interfaces x' where x is the 10G interface connecting to the Quanta...
10-21-2018 07:46 AM - edited 10-21-2018 07:57 AM
This 10Gb interface conf
#show interfaces TenGigabitEthernet1/0/1 TenGigabitEthernet1/0/1 is up, line protocol is up (connected) Hardware is Ten Gigabit Ethernet, address is 2cab.ebad.2033 (bia 2cab.ebad.2033) MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 21785000 bits/sec, 2147 packets/sec 5 minute output rate 511000 bits/sec, 691 packets/sec 132142639 packets input, 177222892076 bytes, 0 no buffer Received 11534 broadcasts (10285 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 10285 multicast, 0 pause input 0 input packets with dribble condition detected 46423933 packets output, 44835656782 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
#show interfaces TenGigabitEthernet1/0/2 TenGigabitEthernet1/0/2 is down, line protocol is down (notconnect) Hardware is Ten Gigabit Ethernet, address is 2cab.ebad.2034 (bia 2cab.ebad.203 4) MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 03:16:19, output 03:16:13, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 2160600185 packets input, 2281618798453 bytes, 0 no buffer Received 1192673 broadcasts (1053296 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 1053296 multicast, 0 pause input 0 input packets with dribble condition detected 1226950055 packets output, 888880464849 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
Show Conf
Using 3383 out of 524288 bytes ! ! Last configuration change at 12:34:22 CET Sun Jan 7 2018 by Cisco ! NVRAM config last updated at 12:39:12 CET Sun Jan 7 2018 ! version 15.2 no service pad service timestamps debug datetime localtime service timestamps log datetime localtime service password-encryption ! hostname C2960XR#1 ! boot-start-marker boot-end-marker ! enable secret 5 $***************************************. enable password 7 1****************** ! username Cisco privilege 15 secret 5 $******$*********. no aaa new-model clock timezone CET 1 0 clock summer-time CET recurring last Sun Mar 1:00 last Sun Oct 1:00 switch 1 provision ws-c2960xr-48lpd-i system mtu routing 1500 ! ! ! ! crypto pki trustpoint TP-self-signed-3************ enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3********** revocation-check none rsakeypair TP-self-signed-3************ ! ! crypto pki certificate chain TP-self-signed-3*********** certificate self-signed 01 nvram:IOS-Self-Sig#1.cer ! spanning-tree mode pvst spanning-tree extend system-id ! ! ! interface Bluetooth0 no ip address shutdown downshift disable ! interface FastEthernet0 no ip address shutdown ! interface GigabitEthernet1/0/1 ! interface GigabitEthernet1/0/2 ! interface GigabitEthernet1/0/3 ! interface GigabitEthernet1/0/4 ! interface GigabitEthernet1/0/5 ! interface GigabitEthernet1/0/6 ! interface GigabitEthernet1/0/7 ! interface GigabitEthernet1/0/8 ! interface GigabitEthernet1/0/9 ! interface GigabitEthernet1/0/10 ! interface GigabitEthernet1/0/11 ! interface GigabitEthernet1/0/12 ! interface GigabitEthernet1/0/13 ! interface GigabitEthernet1/0/14 ! interface GigabitEthernet1/0/15 ! interface GigabitEthernet1/0/16 ! interface GigabitEthernet1/0/17 ! interface GigabitEthernet1/0/18 ! interface GigabitEthernet1/0/19 ! interface GigabitEthernet1/0/20 ! interface GigabitEthernet1/0/21 ! interface GigabitEthernet1/0/22 ! interface GigabitEthernet1/0/23 ! interface GigabitEthernet1/0/24 ! interface GigabitEthernet1/0/25 ! interface GigabitEthernet1/0/26 ! interface GigabitEthernet1/0/27 ! interface GigabitEthernet1/0/28 ! interface GigabitEthernet1/0/29 ! interface GigabitEthernet1/0/30 ! interface GigabitEthernet1/0/31 ! interface GigabitEthernet1/0/32 ! interface GigabitEthernet1/0/33 ! interface GigabitEthernet1/0/34 ! interface GigabitEthernet1/0/35 ! interface GigabitEthernet1/0/36 ! interface GigabitEthernet1/0/37 ! interface GigabitEthernet1/0/38 ! interface GigabitEthernet1/0/39 ! interface GigabitEthernet1/0/40 ! interface GigabitEthernet1/0/41 ! interface GigabitEthernet1/0/42 ! interface GigabitEthernet1/0/43 ! interface GigabitEthernet1/0/44 ! interface GigabitEthernet1/0/45 ! interface GigabitEthernet1/0/46 ! interface GigabitEthernet1/0/47 ! interface GigabitEthernet1/0/48 ! interface GigabitEthernet1/0/49 ! interface GigabitEthernet1/0/50 ! interface TenGigabitEthernet1/0/1 ! interface TenGigabitEthernet1/0/2 ! interface Vlan1 ip address 192.168.1.233 255.255.255.0 ! ip default-gateway 192.168.1.1 ip forward-protocol nd no ip http server ip http authentication local ip http secure-server ! ! vstack ! line con 0 password 7 1******************************** login line vty 0 4 password 7 0**************************************** login line vty 5 15 password 7 1**************************************** login ! ntp server pool.ntp.org ntp server ntp.deuza.net ! end
10-21-2018 08:43 AM
Hello,
check if the Qanta uses the same MTU. On the 2960X, you could try and set the system mtu jumbo size:
C2960XR#1(config)# system mtu jumbo 9000
10-21-2018 09:55 AM
MTU size on Quanta = 1500
#show ip interface 0/19 Routing Interface Status....................... Down Method......................................... None Routing Mode................................... Disable Administrative Mode............................ Enable Forward Net Directed Broadcasts................ Disable Proxy ARP...................................... Enable Local Proxy ARP................................ Disable Active State................................... Active Link Speed Data Rate........................... 10000 Full MAC address.................................... 54:AB:3A:58:B5:3F Encapsulation Type............................. Ethernet IP MTU......................................... 1500 Bandwidth...................................... 10000000 kbps Destination Unreachables....................... Enabled ICMP Redirects................................. Enabled
MTU size on 2960XR = 1500
system mtu routing 1500
Does i need to change it on both to have 10Gb ?
Does it can affect my other device like PC and my router ?
Best Regards.
10-21-2018 10:02 AM
Hello,
don't change it, I just wanted to check if both are the same, which they are.
Can you enable 'mls qos' globally and post the output of:
show mls qos queue-set
show mls qos maps dscp-output-q
10-21-2018 10:10 AM - edited 10-21-2018 10:12 AM
How to enable it ?
Current result with the command
C2960XR#1#show mls qos queue-set Queueset: 1 Queue : 1 2 3 4 ---------------------------------------------- buffers : 25 25 25 25 threshold1: 100 200 100 100 threshold2: 100 200 100 100 reserved : 50 50 50 50 maximum : 400 400 400 400 Queueset: 2 Queue : 1 2 3 4 ---------------------------------------------- buffers : 25 25 25 25 threshold1: 100 200 100 100 threshold2: 100 200 100 100 reserved : 50 50 50 50 maximum : 400 400 400 400 C2960XR#1#show mls qos maps dscp-output-q Dscp-outputq-threshold map: d1 :d2 0 1 2 3 4 5 6 7 8 9 ------------------------------------------------------------ 0 : 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 1 : 02-01 02-01 02-01 02-01 02-01 02-01 03-01 03-01 03-01 03-01 2 : 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 03-01 3 : 03-01 03-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 4 : 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 04-01 04-01 5 : 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 04-01 6 : 04-01 04-01 04-01 04-01
10-21-2018 10:25 AM
Hello,
also post the output of:
sh mls qos inter TengigabitEthernet1/0/1 stat
10-21-2018 10:38 AM
What are your configuration options under the TenGigabitEthernet, is there something like 'media-type' ?
10-21-2018 11:31 PM - edited 10-21-2018 11:34 PM
Output result :
C2960XR#1>enable Password: C2960X#1#sh mls qos inter te C2960X#1#sh mls qos inter tenGigabitEthernet 1/0/1 TenGigabitEthernet1/0/1 QoS is disabled. When QoS is enabled, following settings will be applied trust state: not trusted trust mode: not trusted trust enabled flag: ena COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none qos mode: port-based C2960XR#1#sh mls qos inter tenGigabitEthernet 1/0/2 TenGigabitEthernet1/0/2 QoS is disabled. When QoS is enabled, following settings will be applied trust state: not trusted trust mode: not trusted trust enabled flag: ena COS override: dis default COS: 0 DSCP Mutation Map: Default DSCP Mutation Map Trust device: none qos mode: port-based
Both 10Gb Interface détails on Cisco switch
Media type = media type is SFP-10GBase-SR, but i don't think that what you mean ?
C2960XR#1#sh interface tenGigabitEthernet 1/0/1 TenGigabitEthernet1/0/1 is up, line protocol is up (connected) Hardware is Ten Gigabit Ethernet, address is 046c.9db0.e21b (bia 046c.9db0.e21b) MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:09, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 861000 bits/sec, 559 packets/sec 5 minute output rate 95273000 bits/sec, 8108 packets/sec 1311875793 packets input, 937152365569 bytes, 0 no buffer Received 271735 broadcasts (198300 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 198300 multicast, 0 pause input 0 input packets with dribble condition detected 2387229040 packets output, 2568659777865 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out C2960XR#1#sh interface tenGigabitEthernet 1/0/2 TenGigabitEthernet1/0/2 is up, line protocol is up (connected) Hardware is Ten Gigabit Ethernet, address is 046c.9db0.e21c (bia 046c.9db0.e21c) MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 72585000 bits/sec, 6192 packets/sec 5 minute output rate 682000 bits/sec, 476 packets/sec 2383291379 packets input, 2567994149659 bytes, 0 no buffer Received 685973 broadcasts (549882 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 549882 multicast, 3423 pause input 0 input packets with dribble condition detected 1308770594 packets output, 935310918001 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
10-22-2018 12:17 AM
Hello,
can you enable qos:
2960X#conf t
2960(config)#mls qos
10-22-2018 12:33 AM
Enabled... need to do what after ?
10-22-2018 12:56 AM
Hello,
now post the output of:
sh mls qos inter TengigabitEthernet1/0/1 stat
10-22-2018 08:19 AM
Output result of both 10Gb interace (1x is PC, the other to Quanta LB6M switch)
C2960XR#1#sh mls qos inter tenGigabitEthernet 1/0/1 stat TenGigabitEthernet1/0/1 (All statistics are in packets) dscp: incoming ------------------------------- 0 - 4 : 1294046853 0 0 0 94808454 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 0 0 0 0 30 - 34 : 0 0 0 0 0 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 6 0 15900 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 dscp: outgoing ------------------------------- 0 - 4 : 2636021397 0 0 0 169872 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 0 0 0 0 30 - 34 : 0 0 0 0 71552 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 27427 0 11823 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 cos: incoming ------------------------------- 0 - 4 : 1389195580 0 0 0 0 5 - 7 : 0 0 0 cos: outgoing ------------------------------- 0 - 4 : 2636510590 96 0 0 49 5 - 7 : 0 11814 591716 output queues enqueued: queue: threshold1 threshold2 threshold3 ----------------------------------------------- queue 0: 0 0 0 queue 1: 242532583 27523 604361 queue 2: 0 0 0 queue 3: 0 0 2393949805 output queues dropped: queue: threshold1 threshold2 threshold3 ----------------------------------------------- queue 0: 0 0 0 queue 1: 0 0 0 queue 2: 0 0 0 queue 3: 0 0 0 Policer: Inprofile: 0 OutofProfile: 0 C2960XR#1#sh mls qos inter tenGigabitEthernet 1/0/2 stat TenGigabitEthernet1/0/2 (All statistics are in packets) dscp: incoming ------------------------------- 0 - 4 : 1934073232 0 0 0 0 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 0 0 0 0 30 - 34 : 0 0 0 0 0 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 0 0 0 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 dscp: outgoing ------------------------------- 0 - 4 : 1299890382 0 0 0 85032601 5 - 9 : 0 0 0 0 0 10 - 14 : 0 0 0 0 0 15 - 19 : 0 0 0 0 0 20 - 24 : 0 0 0 0 0 25 - 29 : 0 0 0 0 0 30 - 34 : 0 0 0 0 3 35 - 39 : 0 0 0 0 0 40 - 44 : 0 0 0 0 0 45 - 49 : 0 0 0 16767 0 50 - 54 : 0 0 0 0 0 55 - 59 : 0 0 0 0 0 60 - 64 : 0 0 0 0 cos: incoming ------------------------------- 0 - 4 : 2639015619 0 0 0 0 5 - 7 : 0 0 0 cos: outgoing ------------------------------- 0 - 4 : 1385051248 0 0 0 1 5 - 7 : 0 1623 673132 output queues enqueued: queue: threshold1 threshold2 threshold3 ----------------------------------------------- queue 0: 0 0 0 queue 1: 64172111 12 674776 queue 2: 0 0 0 queue 3: 0 0 1320879105 output queues dropped: queue: threshold1 threshold2 threshold3 ----------------------------------------------- queue 0: 0 0 0 queue 1: 0 0 0 queue 2: 0 0 0 queue 3: 0 0 0 Policer: Inprofile: 0 OutofProfile: 0
10-22-2018 11:57 AM
Hello,
based on your output, configure the below on your interfaces:
interface TenGigabitEthernet1/0/1
mls qos queue-set output 1 buffers 0 10 0 90
srr-queue bandwidth share 1 10 1 80
!
interface TenGigabitEthernet1/0/2
mls qos queue-set output 1 buffers 0 10 0 90
srr-queue bandwidth share 1 10 1 80
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide