10-29-2012 11:33 PM - edited 03-04-2019 06:00 PM
Hi all,
I am experiencing a strange problem with a ASR1002 router that I just installed.thsi is a point to point link .the link is working but for some reason the txload on interface g0/0/0 show 255/255 even though there is no traffic going over to this router.
Thanks in advance for any suggestions !!!
Please see the below interface status for both router.
Router#sh int gi0/0/3
GigabitEthernet0/0/3 is up, line protocol is up
Hardware is 4XGE-BUILT-IN, address is a493.4c98.db03 (bia a493.4c98.db03)
Description: "100Mbps LINK"
Internet address is 10.172.20.110/30
MTU 9100 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 255/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full Duplex, 100Mbps, link type is auto, media type is T
output flow-control is on, input flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:46:49, output 00:00:29, output hang never
Last clearing of "show interface" counters never
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 7000 bits/sec, 4 packets/sec
5 minute output rate 5000 bits/sec, 2 packets/sec
17890 packets input, 9074660 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 7503 multicast, 0 pause input
10137 packets output, 2803120 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Router#
-------------------------------------------------------------------------------------------------------------------------------------------------------------
RP/0/RSP0/CPU0:ASR-9010#sh int Gi0/0/0/13
Tue Oct 30 11:32:10.104 ist
GigabitEthernet0/0/0/13 is up, line protocol is up
Interface state transitions: 11
Hardware is GigabitEthernet, address is 18ef.63e8.6ce7 (bia 18ef.63e8.6ce7)
Description: "100Mbps , Gi0/0/0/13"
Internet address is 10.172.20.109/30
MTU 9114 bytes, BW 100000 Kbit (Max: 100000 Kbit)
reliability 253/255, txload 0/255, rxload 0/255
Encapsulation ARPA,
Full-duplex, 100Mb/s, THD, link type is force-up
output flow control is off, input flow control is off
loopback not set,
ARP type ARPA, ARP timeout 04:00:00
Last input 00:00:00, output 00:00:00
Last clearing of "show interface" counters 22w6d
30 second input rate 3000 bits/sec, 0 packets/sec
30 second output rate 8000 bits/sec, 3 packets/sec
665819 packets input, 159562042 bytes, 5896 total input drops
1 drops for unrecognized upper-level protocol
Received 21 broadcast packets, 99558 multicast packets
350 runts, 1154 giants, 0 throttles, 0 parity
5895 input errors, 2545 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
2154457 packets output, 748147945 bytes, 0 total output drops
Output 14647 broadcast packets, 1490193 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
11 carrier transitions
RP/0/RSP0/CPU0:ASR-9010#
Solved! Go to Solution.
11-08-2012 03:33 PM
This is due to the known defect -
Show interface X/Y returns output with counter txload 255/255
which was duplicated to CSCtr15153
Please use the Bug Tool Kit and verify your the IOS is affected or not.
http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
- HTH
Rahul
11-08-2012 04:49 PM
I agree with Rahul. This is a bug. This bug was fixed on IOS version 15.2(2)S (aka 3.6.0).
11-14-2012 01:20 PM
ASIC Post initialization failed
Hardware failure. There's nothing you can do about it except contact Cisco TAC and have the ME3800X RMA-ed.
11-08-2012 03:33 PM
This is due to the known defect -
Show interface X/Y returns output with counter txload 255/255
which was duplicated to CSCtr15153
Please use the Bug Tool Kit and verify your the IOS is affected or not.
http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
- HTH
Rahul
11-14-2012 03:56 AM
Thanks BOSS it working
11-08-2012 04:49 PM
I agree with Rahul. This is a bug. This bug was fixed on IOS version 15.2(2)S (aka 3.6.0).
11-14-2012 03:57 AM
BOSS you are right .after upgrade it working.
thanks
11-14-2012 03:59 AM
I found a new problem in a new L3 Switch ME 3800X. It repeatedly restarts while I am swiching it on. Through the consol its showing errors after flash initialization. If Im breaking the operation it redirects it to switch prompt (switch:).
Errors:
1.Asic1, PB0 Training Failed.
2.ASIC Post initialization failed
3.driver class subsystem initialization failed
If anyone has a solution please help me.
11-14-2012 01:20 PM
ASIC Post initialization failed
Hardware failure. There's nothing you can do about it except contact Cisco TAC and have the ME3800X RMA-ed.
11-15-2012 05:40 AM
Finally today i logged in Cisco TAC
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide