What I am trying to do: Simply authenticate and login to a Cisco Cloud Services Platform GUI or CLI via RADIUS with admin-group privilege (or any group). CSP is standalone, basic config, just the built-in admin super-user present. Reachability to ...
Forum Posts
Hello, I upgraded the DCNM to 11.3(1) but after that, I cannot open the Data Center Network Manager for SAN (please see image attached)... I found this workaround but not lucky... https://kb.informatica.com/solution/23/Pages/70/572867.aspx?PageVersio...
Hello Im getting message when trying to associate service profile iSCSI VLAN is not native in overlay vNICissue with boot order, possibly iSCSI vNIC not found or no targets configured for iSCSI vnic or same iSCSI vnic is used for both primary and se...
Am I able to configure interface flow monitoring on a N5K-C5548UP System version: 7.3(8)N1(1)
Hi, I have an Iot server configured on one of my packet tracer files, and for some reason when I try to create conditions at my Iot Registration server I click ok but the condition I made doesn't show up, as if it is invisible. Can anyone tell me how...
I have 3 out of box C220 m6. 2 on the network and 1 waiting. The 2 on the network have the same issue so it has to be something i missed in the config/install of ESX. CIMC is reachable. ESX can ping itself but not the gateway. Both CIMC and ESX are...
Resolved! JTAG PIN definition of Nexus X25
Due to it seems that Cisco support portal doesn’t work now, a little question about X25 described here. Could you help provide us the definition of JTAG PINs(14 in total) on X25 for customer’s evaluation on FDK development?
Hi guys. I have two units with separate networks that are connected to the core switch through static route(I have attached the network schematic image below ). I want to monitor the traffic of my clients who are in different units in a span server b...
I need help with Ip routing my instructor told me to use You need to change the subnet mask to 255.255.255.224. This is the reason devices plugged into Swtich2 aren’t working for DHCP. You have them all plugged into VLAN 10, you should move some o...
so im following a guided assignment and I have no clue what problem I'm running into so mainly I have to connect my packet tracer to a internet cloud packet tracer but I'm having a problem with first switch my PC1 and server1 is suppose to connect to...
Rapid 7 is complaining about the following vulnerabilities on my UCS. Specifically the KVMs.I am unclear on how to secure these.I cannot putty to them using the UCS credentials. Untrusted TLS/SSL server X.509 certificate Self-signed TLS/SSL certifica...
hi there, greetings of the day, I write to you because i need to configure CIMC Network Settings (APIC Controller) but i found IP (Basic) Section without parameters so i don't know what i'm configuring; for instance what are the four groups of bracke...
I have installed CVR-QSFPSFP10G with 10G LR ,both are 3rd party inside the N9K-C9332D-GX2B but I can't see them in any show command.The software version is compatible, the optics are working if I plug them in 10G ports.Tested the CVR-QSFPSFP10G ...
We have a UCS C240 M4S2 that has not been updated since it was installed 5 or so years ago. One of the drives in the RAID 5 array has failed, and we have a replacement for it. This server is slated to be replaced (lol should have been done last ye...
Hello Community,I am currently working on an Embedded Event Manager (EEM) script that triggers a Python script whenever a specific event occurs on a Nexus 9.3 switch. The Python script generates a table that I want to display to the user directly on ...
