Hi,I've developed a management pack to monitor devices in Cisco DNA center via SCOM. The management pack uses the API to collect data and to alert when a device that is in Cisco DNA Center is unreachable. This helps to make SCOM the single pane of gl...
Forum Posts
Hello, such a question for you: I am doing the work 2.5.2.7 Packet Tracer, according to the task, you need to follow the link http://www.cisco.corp to download files, but it says to me that Host Name Unresolved, no matter how I try to do it , still d...
We have a server that's been off warranty for a few months. It only has 32GB of RAM, but it's heavily used everyday. It's used to run ExacQvision camera software, monitoring activity in our Testing Center with 61 HD cameras. Lately it's performance h...
I have a pair of Nexus 5548s in the lab. I'm trying to build a VPC to a C220M3 using a P81E adapter. I cannot get the int port-channel 30/vpc 30 to come up. Any ideas?B5548# show vpcLegend: (*) - local vPC is down, forwarding via vPC p...
Hi All,I'm working on a VXLAN deployment and although I can find lots of information about how to deploy VXLAN I can't find any information about options for routing between the VXLAN VRFs and the undelay routing protocol which is required for client...
Dear all, I created to RAID-1 as virtual hard-drive in order to install Vmware and later cisco NCS software at ciscı C220 M3. I followed the all the procudure then l was succesfull to istallation of softwares. I just a small problem that when ı re...
Hello!I'm trying to get information regarding the power up and testing requirements for a few UCS 5108 Chassis and M3,M4, and M5 Blades I have on hand in my company's refurb shop. I've found dozens of videos demonstrating how to put the chassis in t...
Read articles all over about ntp and vdcs, but cant seem to figure it out. N7706-01-CORE(config)# ntp commitFabric Distribution not enabled for NTPN7706-01-CORE(config)# show run | inc ntpntp server 172.24.0.202ntp server 172.24.254.9 prefer use-vrf...
Hi All Currently have a racking scenario for a UCS Infratsrtructure where the 100GBASE QSFP to 4xSFP25G Passive Copper Splitter Cables at 5 Meters isn't quite long enough, yet there isn't a 7 or 10 Meter Cable available from CIsco. Does anyone know ...
Hi everyone, Need some help here...I am configuring vPC between two Nexus 9K, C93240YC-FX2. Port-channel 10 is the vPC peer link and is up. However, "show vpc" shows peer link is down. I have tried to re-configure vpc, port-channel, shut/un-shut vpc,...
Hi All, I have a strange situation, my UCS C220-M7 always prompt : current default password not match if I try change default password of CIMC at first time.I had try lot of password as: password, Cisco1234, Cisco12345,... but still can not change CI...
Hello,Is it possible to swap the PSU and fans from port-side exhaust to port side intake of a Nexus 93240YC-FX2? Or the entire switch has to be replaced to change the air flow? Can't find any docs that says it's possible. Thanks.
I'm planning the details of how to configure our new 9300 switches (2 each in 2 DC's, connected by 2 runs of dark-fibre) Is there anything that I need to be aware of that will not work? I haven't been able to find much in the way of documentation for...
Hi Community, I have a UCS Servers with Fabric Interconnect and I'm doing troubleshooting because I see CRC errors on several IOM ports, I ran the command # show platform fwm info asic-errors 0 to determinate the cause of those errors, in the field D...
Hello everyone,I've been trying to setup Secure Syslog for hours, but I can't get it to work. I tried following the NX-OS System Management Configuration Guide, but it doesn't go really in depth on the topic. This is what I did:conf tlogging server I...
