cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

887
Views
0
Helpful
2
Replies
Beginner

How to replace Nexus5596 with dual-homing N2K

What is the correct process to replace a FEX parent switch with dual-homing fex?

Traffic should not be interrupted.        

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Beginner

How to replace Nexus5596 with dual-homing N2K

Hi

Do you have VPC between Parent Switches & are you running VPC on dual homed FEX fabric ports. ?

If yes Below is the procedure,

1)  boot the replacement switch without VPC, peer-links & FEX ports connected to it.

2)  Make sure it has same Software version matches with the peer switch.

3)  enable Pre-Provisioning for slots with appropriate FEX model.

, here find the guide:

http://www.cisco.com/en/US/partner/docs/switches/datacenter/nexus5000/sw/system_management/521_n1_1/b_5k_System_Mgmt_Config_521N11_chapter_0100.html#task_05BB53AD7AFB49CF9A8E4A5C6C37CB38

So, on the replacement switch you will pre-provision the Fabric Extender and configure the ports so it will be ready when you add the module to the RMA SW.

Please make sure you put the appropriate FEX model on the provision slot, otherwise, when connected it will not come Online

Example, FEX 110:

N5K(config)# slot 110

N5K(config-slot)#provision model N2K-C2248T

4) Now  keep all ports at Shut down state Then Configure Entire switch that includes FEX host ports, FEX Fabric Ports & VPC peer-link, VPC Domain Configuration.

keep FEX host ports in shut state.

5)  keep VPC Role priority on existing switch lower than , new switch

6) Connect Peer-link ports to Peer switch & wait till VPC Comes up-

7) Then connect Fabric ports from FEX to the pre-configured ports on replacement switch

After it comes online Unshut FEX host ports.

I got similar steps here as well

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/operations/n5k_vpc_ops.html#wp425197

NOTE: I followed same process however, few ping drops were seen....arnd ( 5- 6 ping loss) only on few hosts...

Mazhar

2 REPLIES 2
Highlighted
Beginner

How to replace Nexus5596 with dual-homing N2K

Hi

Do you have VPC between Parent Switches & are you running VPC on dual homed FEX fabric ports. ?

If yes Below is the procedure,

1)  boot the replacement switch without VPC, peer-links & FEX ports connected to it.

2)  Make sure it has same Software version matches with the peer switch.

3)  enable Pre-Provisioning for slots with appropriate FEX model.

, here find the guide:

http://www.cisco.com/en/US/partner/docs/switches/datacenter/nexus5000/sw/system_management/521_n1_1/b_5k_System_Mgmt_Config_521N11_chapter_0100.html#task_05BB53AD7AFB49CF9A8E4A5C6C37CB38

So, on the replacement switch you will pre-provision the Fabric Extender and configure the ports so it will be ready when you add the module to the RMA SW.

Please make sure you put the appropriate FEX model on the provision slot, otherwise, when connected it will not come Online

Example, FEX 110:

N5K(config)# slot 110

N5K(config-slot)#provision model N2K-C2248T

4) Now  keep all ports at Shut down state Then Configure Entire switch that includes FEX host ports, FEX Fabric Ports & VPC peer-link, VPC Domain Configuration.

keep FEX host ports in shut state.

5)  keep VPC Role priority on existing switch lower than , new switch

6) Connect Peer-link ports to Peer switch & wait till VPC Comes up-

7) Then connect Fabric ports from FEX to the pre-configured ports on replacement switch

After it comes online Unshut FEX host ports.

I got similar steps here as well

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/operations/n5k_vpc_ops.html#wp425197

NOTE: I followed same process however, few ping drops were seen....arnd ( 5- 6 ping loss) only on few hosts...

Mazhar

Beginner

How to replace Nexus5596 with dual-homing N2K

Thanks a lot

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards