01-08-2016 07:51 AM
I read an update stating that after version 6.2 in the N7K that F2E and M1 cards can be mixed in the same VDC. I am running version 6.2.(8a). Only the ports for the M1 card are available and I tried add the ports from the F2 cards to vdc 1 and its says its not supported. I know the only way I was able to get this to work by creating a separate VDC for the F card and leaving the M card in VDC1. The customer doesn't plan to use any VDC's only needs L3 functionality and L2 functionality to segment any non L3 ports into VLANs. What can I do to make sure the ports from the F2 cards are available to use.
switch(config-vdc)# allocate interface e2/1-48
Moving ports will cause all config associated to them in source vdc to be removed. Are you sure you want to move the ports (y/n)? [yes] yes
ERROR: 1 or more interfaces are from a module of type not supported by this vdc
switch(config-vdc)#
I have a N7K with these cards:
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 48 10/100/1000 Mbps Ethernet Module N7K-M148GT-11 ok
2 48 1/10 Gbps BASE-T Ethernet Module N7K-F248XT-25E ok
3 48 1/10 Gbps BASE-T Ethernet Module N7K-F248XT-25E ok
4 48 1/10 Gbps BASE-T Ethernet Module N7K-F248XT-25E ok
5 0 Supervisor Module-2 N7K-SUP2E active *
6 0 Supervisor Module-2 N7K-SUP2E ha-standby
Mod Sw Hw
--- -------------- ------
1 6.2(8a) 1.5
2 6.2(8a) 1.2
3 6.2(8a) 1.2
4 6.2(8a) 1.2
5 6.2(8a) 1.1
6 6.2(8a) 1.1
switch# show vdc member
Flags : b - breakout port
---------------------------------
vdc_id: 0 vdc_name: Unallocated interfaces:
Ethernet2/1 Ethernet2/2 Ethernet2/3
Ethernet2/4 Ethernet2/5 Ethernet2/6
Ethernet2/7 Ethernet2/8 Ethernet2/9
Ethernet2/10 Ethernet2/11 Ethernet2/12
Ethernet2/13 Ethernet2/14 Ethernet2/15
etc..
vdc_id: 1 vdc_name: switch interfaces:
Ethernet1/1 Ethernet1/2 Ethernet1/3
Ethernet1/4 Ethernet1/5 Ethernet1/6
Ethernet1/7 Ethernet1/8 Ethernet1/9
Ethernet1/10 Ethernet1/11 Ethernet1/12
Ethernet1/13 Ethernet1/14 Ethernet1/15
(only shows ports for the M card)
switch# show vdc detail
Switchwide mode is m1 f1 m1xl f2 m2xl f2e f3
vdc id: 1
vdc name: switch
vdc state: active
vdc mac address: 00:26:98:23:5b:c1
vdc ha policy: RELOAD
vdc dual-sup ha policy: SWITCHOVER
vdc boot Order: 1
CPU Share: 5
CPU Share Percentage: 100%
vdc create time: Fri Jan 8 09:57:30 2016
vdc reload count: 0
vdc uptime: 0 day(s), 22 hour(s), 58 minute(s), 58 second(s)
vdc restart count: 0
vdc type: Ethernet
vdc supported linecards: m1 f1 m1xl m2xl
switch#
switch#
switch#
switch# show inter bri
--------------------------------------------------------------------------------
Port VRF Status IP Address Speed MTU
--------------------------------------------------------------------------------
mgmt0 -- down -- -- 1500
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Por
t
Interface Ch
#
--------------------------------------------------------------------------------
Eth1/1 -- eth routed up none 1000(D) --
Eth1/2 -- eth routed down Administratively down auto(D) --
Eth1/3 -- eth routed down Administratively down auto(D) --
Eth1/4 -- eth routed down Administratively down auto(D) --
Eth1/5 -- eth routed down Administratively down auto(D) --
etc..
Eth1/48 -- eth routed down Administratively down auto(D) --
-------------------------------------------------------------------------------
Interface Secondary VLAN(Type) Status Reason
-------------------------------------------------------------------------------
Vlan1 -- down Administratively down
switch#
01-08-2016 10:55 AM
Can you post the output of "show vdc" and "show run vdc" from the default vdc
I think the vdc type for VDC 1 probably does not include the M-F combination hence you are getting the error. The show outpus should give a clear picture on what is needed to get the F card added into this vdc.
-Raj
01-08-2016 11:10 AM
Yup I resolved this by trying this:
config t
vdc switch
limit-resource module-type m1 f2e
switch# show vdc
Switchwide mode is m1 f1 m1xl f2 m2xl f2e f3
vdc_id vdc_name state mac
type lc
------ -------- ----- ----------
--------- ------
1 switch active
Ethernet m1 f2e
switch#
Thanks for your reply!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide