Hello!I have DNAC version 2.1.2.5 and SD access fabric based on two C9300-48U switches: one border&control plane node, another - edge node.I create one VN network USERS with one IP network and try to configure routing with server out of fabric but ha...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Hi, I have 2 border nodes running as L3 between them in a SDA design. I would like to perform LAN automation for new fabric edges and they have dual-homed link to both borders. How do perform LAN automation to select both borders?
Resolved! Ring of Edge nodes supported?
Hello, Is such topology supported in SDA? Any official documentation?(Access switches defined as Edge nodes, not as Extended nodes. All links configured as Layer3). If yes, any pros or cons you might think of? Thanks,Sylvain.
Resolved! SD-Access , SD-WAN Transit
Hi, I know there are three sd-access transit types : Cisco SD-Access Transit IP- Based Transit Cisco SD-WAN Transit in the Cisco DNA center i can find only below configuration , which I can configure only SD-Access Transit or IP-Based Transit but...
In the Anycast Gateway configuration there is the option to assign a Security Group.My understanding is if a port has any other authentication than "None" the Security Group would be allocated by ISE.For "None" ports I can assign a VLAN and optionall...
Resolved! I'm SDA Student
Greeting~~~ I'm a beginner at Cisco SDA.To start studying SDA, I'm looking for an image of GNS3. I have images below;- NX-OSv 9500v 10.1.1- Cat 8000V 17.15.01a- ISE 2.7.0.356 On those images, I am unable to practice EVPN. I'm looking forward to hear...
Hello guys,I am trying to do SGT Role enforcement on the Fabric Border. It works by making an SXP connection on the Fabric Borders with the ISE PSNs. It works at first, all the IP-SGT Bindings are successfully downloaded. However, after some time all...
Hi all we are going to upgrade the ACI fabric from 5.2(8e) to 6.0(8f) and also wanted to upgrade CIMC, for ACI we already prepare the plan but need all the information regarding CIMC upgradation with pre and post checks.. Can someone help??
We have written some software that uses openflow to control routing through a switch. Currently, this is integrated with OpenVSwitch, but we have been trying to integrate it with the Cisco Catalyst 9300.Our software sends two initial Flow-Mod command...
Do the Cisco SD-Access control plane node scale numbers listed in the data sheets include MAC address + IPv4 address + IPv6 address, or just client counts. For example does a single dual stack client count as 3 or more database entries in the contro...
I have a setup that need to be implemented where DNAC would forward the required SNMP trap messages copy that it receives from SNMP client to external server running O-insight ( milestone) server. As per the proposal, the O-insight is only interes...
I want to delete the Cedge router configuration from vmanage, do anyone have any idea how we do that remotely..Via vManage or through cli..
Hi all,i have a very small remote site that is currently connected via an L2 Point-to-Point link to our headquarters. The site is provided with two stacked 9300L switches and four 9120AXI APs and is working as a "streched site" so 9300L switches are ...
Resolved! Pxgrid enable in pan or PSN or both
Hi team, We have a six node deployment with 2 admin plus mnt 4 PSN. For ftd integration in which node we need to enable pxgrid persona and why? Thanks in advance
Hi Team, Is anyone have a complete guide for Aruba switch side dot1x configuration guide. If yes please share it here and also how to integrate Aruba switch in Cisco ISE. Is it just like a normal process of add network device or different
