Hi team, does DNA center supports SD-WAN integration and can SD-WAN routers be Border/control nodes for remote branch sites for SDA? I have seen and read integration option in DNA center, but it is called "vedge provisioning ". But i don't sure that ...
Hello. In my fabric network cisco 9500series stack is acting as Fusion. I have configured DNS Server on it to server as proxy to my clients. Last 3 days we have been doing migration to office and I had to change 9500 and reconfigure from 0 again and ...
Hi, Is it possible to have in the same physical site 2 SD-Access fabrics, one dedicated for wireless network only and the other dedicated for Wired network only, and - Both fabrics will be managed by the same DNAC - Both fabrics will use the sam...
I am wondering how HA is supported for SDA EWC on Cat 9500’s? Can 2 9500’s acting as a CP/B can with ewc on each 9500 and put then in an SSO pair? Do we have an documentation on how we do SDA Embedded wireless HA and installation guides for this?
In the build process, we initially configured the Guest Wireless settings (Security: Open).Provisioned the Fabric and assigned Wireless SSID's to Address Pools (Provision > Fabric > Fabric Site > Host Onboarding > Wireless SSID's)We conducted testing...
During the LAN automation, is there a way to set your own loopback IP address? Doesn’t appear to be from the GUI. Perhaps through an API?Reason: -Pre-plan adding those IP’s to Tacacs and Radius. Thanks.
Hi All, I'm currently deploying a small pilot SDA fabric for a company. A question has been raised about the need for the fusion router. Now I know what the purpose of the fusion router is, however, is it mandatory in every deployment as we can achie...
I know SD Access can assign a port with closed authentication template for 802.1x authentication. I would like to know can the port authenticate user using eCert authentication?
hello,I have two 9500 switches in stackwise as border node which will be connected to a 9407 switch with two links, I wanted to know is that the two links will be converted into L3 link ?? another question if i stoped the process of the lan automati...
I am setting up a SDA Demo using DNAC 1.3.3.7 and ISE 2.7 patch 1. I will have VN and IP Pool as below Site IP Pool VN ISE VLAN tag ID/Name 1 172.168.1.0/24 Employee1 172_168_1_0-EMPLOYEE1 2 10.1.1.0/24 Employee2 10_1_1_0-EMPLOYEE2 In ISE, I wi...
Hello all!I can not find an answer on my question. Please help The issue:We need to have a number of ports with manual sgt mapping. We may configure it by DNAC as on a picture below.All IP connected to this port are mapped to an appropriate sgt and a...
I am working on a DNAC 1.3.3.7 now. I am confused about the ISE policy element setup for VLAN. From very early EFT guide, there is a statement for ISE VLAN ID/Name setup to match with DNAC IP Pool to Virtual Network: Note: DNA Center will generat...
Hi allSD-Access Fabric running with some Extended Nodes (C3560CX).Clients (Windows) complain about Duplicate IP Adresse. The weird thing is, that the reported MAC address is the MAC address from the Exteneded Nodes - Uplink Interface to the Edge Node...
Hello all! I need some help with simple question:Case: You have DNA\SDA architecture and you want to connect dumb switch for any endpoint devices in SD-Access port (e.g 9300 sw) and you need to auth thes endpoint devices. Again: SDA C9300----dumb SW-...
Hello everyone,I have a multi-site ISE deployment where PAN, MNT are installed at single location. Remaining 4 remote sites having 2 x PSN nodes and 2 x WLCsWe are planning to deploy 3-node DNAC cluster at any one of four remote site.As understood f...
