cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1057
Views
0
Helpful
3
Replies

questions about port-channel

ivy_yangxiaohua
Beginner
Beginner

hi, all

i am a newbie of MDS.

now I have questions about port-channel.

currently we configure port-channel on the MDS(MDS9513), which contains 4 members....and We also have 3 other  port-channel

lasfswcor02# sh interface  port-channel 53

port-channel 53 is up

    Port description is "uslas-c6296fi-01-b"

    Hardware is Fibre Channel

    Port WWN is 24:35:00:05:73:e2:5e:40

    Admin port mode is F, trunk mode is on

    snmp link state traps are enabled

    Port mode is F

    Port vsan is 520

    Speed is 32 Gbps

    5 minutes input rate 492274736 bits/sec, 61534342 bytes/sec, 38284 frames/sec

    5 minutes output rate 3958335744 bits/sec, 494791968 bytes/sec, 261789 frames/sec

      1672665727513 frames input, 2913377399510808 bytes

        0 discards, 0 errors

        0 CRC,  0 unknown class

        0 too long, 0 too short

      5648987822520 frames output, 10407306504402572 bytes

        540 discards, 0 errors

      40 input OLS, 26 LRR, 23 NOS, 0 loop inits

      34 output OLS, 3 LRR, 22 NOS, 9 loop inits

    Member[1] : fc1/1

    Member[2] : fc1/7

    Member[3] : fc2/4

    Member[4] : fc4/28

    Interface last changed at Mon Nov 18 18:23:01 2013

my questions are as below:

1) how do you know which server is using which port-channel ?

2) how do you know how much traffic / or utilization each port is using?

3) how do you see if the port-group is saturated?

Really appreciate your help

thanks in advance!!!!!

1 Accepted Solution

Accepted Solutions

Hi Ivy,

Answers inline:

1) how do you know which server is using which port-channel ?

I assume you meant which inteface in the port channel?

They are load balanced, so each server might at any time be using any of the interfaces.

That is one of the benefits of using a port-channel.  If these were individual interfaces not

in a port channel, the servers would be distributed round robin.  The server would be tied to that

interface, ( which you could see in the show flogi database on the MDS ) and could only use

the bandwidth of that one interface.  Also, if that interface goes down, then the server would have

to log back into the fabric over another interface to the MDS.

2) how do you know how much traffic / or utilization each port is using?

Use Fabric Manager, Device Manager, Cisco Prime Data Center Network Manager or show interface CLI command.

3) how do you see if the port-group is saturated?

Use Fabric Manager, Device Manager, or Cisco Prime Data Center Network Manager.

Best regards,

Jim

View solution in original post

3 Replies 3

ivy_yangxiaohua
Beginner
Beginner

nobody can help me?

Hi Ivy,

Answers inline:

1) how do you know which server is using which port-channel ?

I assume you meant which inteface in the port channel?

They are load balanced, so each server might at any time be using any of the interfaces.

That is one of the benefits of using a port-channel.  If these were individual interfaces not

in a port channel, the servers would be distributed round robin.  The server would be tied to that

interface, ( which you could see in the show flogi database on the MDS ) and could only use

the bandwidth of that one interface.  Also, if that interface goes down, then the server would have

to log back into the fabric over another interface to the MDS.

2) how do you know how much traffic / or utilization each port is using?

Use Fabric Manager, Device Manager, Cisco Prime Data Center Network Manager or show interface CLI command.

3) how do you see if the port-group is saturated?

Use Fabric Manager, Device Manager, or Cisco Prime Data Center Network Manager.

Best regards,

Jim

Thank you Jim

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers