cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5502
Views
0
Helpful
5
Replies

VFC x is trunking. no way to set the host connecting through FCoE

eric.krejci
Level 1
Level 1

Hello,

I have a Nex 5548 version 5.0(3)N1(1b)

at this time release to configure FCoE was simply the steps of mapping VLAN to VANS, creating vfc and adding the vfc to the good vsan..

now I'm stuck.

I've my interface Eth in a PO. I bound the vfc to this po. and when the server boot up, I simply have the vfs stuck in "vfc x is trunking".

sho inter vfc 1258
vfc1258 is trunking
Bound interface is port-channel1258
Port description is "esx58 FAB2"
Hardware is Virtual Fibre Channel
Port WWN is 24:e9:00:05:73:cd:70:ff
Admin port mode is F, trunk mode is on
snmp link state traps are enabled
Port mode is TF
Port vsan is 2
Trunk vsans (admin allowed and active) (2)
Trunk vsans (up)                       ()
Trunk vsans (isolated)                 ()
Trunk vsans (initializing)             (2)
1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
0 frames input, 0 bytes
0 discards, 0 errors
0 frames output, 0 bytes
0 discards, 0 errors
last clearing of "show interface" counters never
Interface last changed at Mon Apr 11 17:23:02 2011

a cannot turn off the trunk mode of the vfc.

let me show you the vfc conf:

interface vfc1258
bind interface port-channel1258
switchport trunk allowed vsan 2
switchport description "esx58 FAB2"
no shutdown

honestly when i run these conf against a Nex 5010 in rev 4.2 it was working straitforward. how can I set this vfc to F mode only?

hope you will help me.

thanks in advance.

Eric

5 Replies 5

Kris Vandecruys
Cisco Employee
Cisco Employee

Hi eric,

this should be as simple as

# conf term

(config)# interface vfc 1258

(config-if)# no switchport trunk allowed vsan all

(config-if)# end

#

HTH

Nice try, but I got this on both host interfaces:

vfc1258 is down (Isolation due to no common vsans with peer on trunk)
Bound interface is port-channel1258
Port description is "ditex-esx58 FAB2"
Hardware is Virtual Fibre Channel
Port WWN is 24:e9:00:05:73:cd:70:ff
Admin port mode is F, trunk mode is on
snmp link state traps are enabled
Port vsan is 2
1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
0 frames input, 0 bytes
0 discards, 0 errors
0 frames output, 0 bytes
0 discards, 0 errors
last clearing of "show interface" counters never
Interface last changed at Mon Apr 11 19:39:17 2011

Eric

Hi Eric

Did you find a solution on this ? I'm having the exact same issue and I have tried just about anything.

Tnx

Claus

Sorry about the delay.

this was related to the fact the Cisco doesn't enable by default the QOS for FCoE on their nes Nexus 55xx switches.

enabling the proper QOS for FCoE can be found on the following page:

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/troubleshooting/guide/n5K_ts_fcoe.html#wp1037424

once done you vfc will come up.

Eric

Hi,

I have the same problem, when running 5.2(1)N1(1). The adapter is an LP21002-C, which is a Generation 2 CNA configured as a "Fabric point to point" interface on the Emulex side.

We've tried setting the QoS as explained in the parent post, to no avail.

When connected to a release 4, things work. When connected to release 5:

# sho int vfc4

vfc4 is down (Initializing)

interface port-channel4

  switchport mode trunk

  switchport trunk allowed vlan 10

  speed 10000

  vpc 4

interface vfc4

  bind interface Ethernet1/4

  no switchport trunk allowed  vsan all

  no shutdown

interface Ethernet1/4

  switchport mode trunk

  switchport trunk allowed vlan 10

  spanning-tree port type edge

  channel-group 4

Review Cisco Networking for a $25 gift card