07-14-2009 04:56 PM
07-14-2009 05:17 PM
07-14-2009 09:08 PM
Zealdcisco,
I just checked Cisco.com and there is a newer firmware version, 1.2.2 available. Your post said you were on 1.2.1. I would upgrade to the newer firmware and see if the upgrade solves the issues.
Jim
07-14-2009 09:34 PM
Hi,
thank you for fast reply, I have seen that firmware, but I am affraid to apply it as I could not find the changelog, and what exactly has been fixed, as I don't want to break it further more, and reverting back to original is difficult.
I also found reports that firmware still does not function properly : http://forums.linksys.com/linksys/board/message?board.id=Switches&thread.id=3486 .
Where can I find the changelog for that firmware (1.2.2)?
I am very cautious with cisco and firmware.
07-15-2009 04:38 PM
http://www.cisco.com/en/US/docs/switches/lan/csbms/srw2048/release/notes/SRW2048_v1.2.2-tm.pdf
SRW2048 Firmware Revision History
Software version 1.2.2 01/01/2007
Boot version 1.0.0.04 08/09/2005
Known Issues
=========
1. ACL --> MAC Based ACL
Creating a MAC ACL with to permit ethertype 0800 causes all traffic to be forwarded. Configuring a MAC ACL to permit ethertype 86DD causes all traffic to be denied.
Recommended Workaround: To avoid these situations, add a rule to deny any any.
2. Admin --> Cable Test
When testing cable with advanced test only (without simple test before), the results are incorrect.
3. QoS --> Advanced Mode
When configuring a policy with police - exceeded action - out of profile dscp, the policy must have an action: trust cos-dscp or set dscp. If you configure a policy with police - exceeded action - out of profile dscp without an action - the device configures the action to trust cos-dscp. If you configure a policy with police - exceeded action - out of profile dscp with an action set cos/queue, the device configures the action to set dscp 0.
4. Setup --> Time
The prioritization between servers is not maintained when two servers are configured simultaneously.
5. SNMP --> Group Membership
It is not possible to modify the user name after it has been entered.
Recommended Workaround: Delete the user and reconfigure.
6. VLAN Management
When a port is a member of Dynamic VLANs and Static VLANs, there may be errors in configuration using the Join VLAN pop up.
Recommended Workaround: Use the Ports to VLAN screen to join ports to VLANs.
7. Timestamps
(a) The order of the month and day in the dates presented in syslog messages is the European fromat (dd/mm/yy), and not the US format.
(b) SNMP traps are sent with a timestamp different from the actual time on the device, since the timestamp depends on the NMS configuration. The sequence is preserved.
8. HTTP port configuration
It is possible to modify the HTTP port to an already used port (e.g., 443). No error message is generated at this point.
9. Illegal characters in web inteface
Use of the following characters should be avoided when configuring using the web based interface: \ / : * ? < > |
10. Menu CLI
(a) Disable Active Management Access Profile - this software version does not support Management ACL, so this option is irrelevant to the user. It is reserved for future use.
"disable active mgmt access profile" is not working in menu console
(b) One cannot change the "admin" password in the Web GUI, but through menu CLI it is available.
GUI doesn't work only if there is only one user "Admin"
If you change the username to Admin1 or anything else, it works.
If you have another user name or names in addition to Admin, then it works too.
Hope this helps.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide