Help needed: SRW224G4P password recovery

[xinyer]

Hi,

I need help with password recovery on SRW224G4P. I couldn't get into the MENU by press ESC to interrupt the normal boot process. I tried many many times, no luck at all.

Below is what I see during boot up process:

Loading Diagnostic Image File : SRW224G4P_SRW248G4P_boot.bix

Diagnostic 1.0.1

User Mode

--- Performing Power-On Self Tests (POST) ---
DUMMY Test 1 ................. PASS
UART Loopback Test ........... PASS
POE UART Loopback Test ....... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
Done All Pass.
------------------ DONE ---------------------

Loading Runtime Image File : SRW224G4P_SRW248G4P_image.bix
Runtime 1.0.2

Pass
root init done

Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
stacking DB: unit = 0, module type = 0

Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
Load certificate files : Starting
Load certificate files : Finished

Finish Master mode ...

Performing startup provision ...
CLI enter main (PROVISION)

................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
..............................................................
Notify provision complete

CLI provision has been completed

Provision Complete ...
Finish Provision Complete ...
[get stackingMac done ret_val] = 1
XFER: End of config sync.

Please press <Enter> to start Menu session!

Please help, let me know where I should press ESC or any other key....

[xinyer]

Pls help.....

[chrcoope]

Use this procedure. I tested it in my lab with your model switch and it worked here.

Regards,

Christopher

[c.alperin]

Ctrl+U should make it on the boot process, and then reset to default configuration

[Ganesh Hariharan]

Hi,
I
need help with password recovery on SRW224G4P. I couldn't get into the
MENU by press ESC to interrupt the normal boot process. I tried many
many times, no luck at all.
Below is what I see during boot up process:
Loading Diagnostic Image File : SRW224G4P_SRW248G4P_boot.bix
Diagnostic 1.0.1
User Mode
--- Performing Power-On Self Tests (POST) ---
DUMMY Test 1 ................. PASS
UART Loopback Test ........... PASS
POE UART Loopback Test ....... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
Done All Pass.
------------------ DONE ---------------------

Loading Runtime Image File : SRW224G4P_SRW248G4P_image.bix
 Runtime 1.0.2

Pass
root init done
Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
stacking DB: unit = 0, module type = 0
Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
Load certificate files : Starting
Load certificate files : Finished
Finish Master mode ...

Hi,

In order for you to reset the SRW224G4P you need to use a Data cable and use the console port of the switch. Once you are on the Console screen you could do a hardware reset.

Check out the below link for more information

http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=16615&p_created=1212523507&p_sid=6PuaAz3k&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9OTA2LDkwNiZwX3Byb2RzPTAmcF9jYX...

Hope to Help !!

Ganesh.H

Remember to rate the helpful post