Dear Aman,
Below output is for your reference, can you please check, in mean time I will do romon with POST method,
Here I try to change "change the boot characteristics", however I am unseccessful, always boot chac valu is 0,, i try to chnage it to 1, 2 and 15, but same result, kinldy look into bold italic output giveb below....
rommon 3 >
rommon 3 >
rommon 3 > confreg
Configuration Summary
(Virtual Configuration Register: 0x0)
enabled are:
break/abort has effect
console baud: 9600
boot: the ROM Monitor
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]: n
enable "use net in IP bcast address"? y/n [n]: n
enable "load rom after netboot fails"? y/n [n]: n
enable "use all zero broadcast"? y/n [n]: n
disable "break/abort has effect"? y/n [n]: n
enable "ignore system config info"? y/n [n]: n
change console baud rate? y/n [n]: n
change the boot characteristics? y/n [n]: y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
[0]: 1
Configuration Summary
(Virtual Configuration Register: 0x1)
enabled are:
break/abort has effect
console baud: 9600
boot: the boot helper image
do you wish to change the configuration? y/n [n]: n
You must reset or power cycle for new config to take effect
rommon 4 > reset
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xe08298
Self decompressing the image : ############################################################################################################################################# [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X0021 0X00035000 Card in slot 0
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 7657322 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen
Image text-base: 0x6008873C, data-base: 0x61485A60
Queued messages:
*Sep 1 11:37:00.359: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Sep 1 11:37:00.291: %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0]
The module in 0/-1/-1 in this router may not be a genuine
Cisco product. Cisco warranties and support programs only
apply to genuine Cisco products. If Cisco determines that
your insertion of non-Cisco memory, WIC cards, AIM cards,
Network Modules, SPA cards, GBICs or other modules into a
Cisco product is the cause of a support issue, Cisco may
deny support under your warranty or under a Cisco support
program such as SmartNet.
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 > confreg
Configuration Summary
(Virtual Configuration Register: 0x0)
enabled are:
break/abort has effect
console baud: 9600
boot: the ROM Monitor
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]: n
enable "use net in IP bcast address"? y/n [n]: n
enable "load rom after netboot fails"? y/n [n]: n
enable "use all zero broadcast"? y/n [n]: n
disable "break/abort has effect"? y/n [n]: n
enable "ignore system config info"? y/n [n]: n
change console baud rate? y/n [n]: n
change the boot characteristics? y/n [n]: y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
[0]: 2
Configuration Summary
(Virtual Configuration Register: 0x2)
enabled are:
break/abort has effect
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-c1841
do you wish to change the configuration? y/n [n]: n
You must reset or power cycle for new config to take effect
rommon 2 > reset
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xe08298
Self decompressing the image : ############################################################################################################################################# [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X0021 0X00035000 Card in slot 0
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 7657014 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen
Image text-base: 0x6008873C, data-base: 0x61486400
Queued messages:
*Sep 1 11:38:19.355: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Sep 1 11:38:19.291: %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0]
The module in 0/-1/-1 in this router may not be a genuine
Cisco product. Cisco warranties and support programs only
apply to genuine Cisco products. If Cisco determines that
your insertion of non-Cisco memory, WIC cards, AIM cards,
Network Modules, SPA cards, GBICs or other modules into a
Cisco product is the cause of a support issue, Cisco may
deny support under your warranty or under a Cisco support
program such as SmartNet.
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 > confreg
Configuration Summary
(Virtual Configuration Register: 0x0)
enabled are:
break/abort has effect
console baud: 9600
boot: the ROM Monitor
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]: n
enable "use net in IP bcast address"? y/n [n]: n
enable "load rom after netboot fails"? y/n [n]: n
enable "use all zero broadcast"? y/n [n]: n
disable "break/abort has effect"? y/n [n]: n
enable "ignore system config info"? y/n [n]: n
change console baud rate? y/n [n]: n
change the boot characteristics? y/n [n]: y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
[0]: 15
Configuration Summary
(Virtual Configuration Register: 0xf)
enabled are:
break/abort has effect
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco17-c1841
do you wish to change the configuration? y/n [n]: n
You must reset or power cycle for new config to take effect
rommon 2 > reset
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xe08298
Self decompressing the image : ############################################################################################################################################# [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X0021 0X00035000 Card in slot 0
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 7654090 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 28-Nov-07 18:17 by stshen
Image text-base: 0x6008873C, data-base: 0x6148BF60
Queued messages:
*Sep 1 11:39:34.351: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Sep 1 11:39:34.291: %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0]
The module in 0/-1/-1 in this router may not be a genuine
Cisco product. Cisco warranties and support programs only
apply to genuine Cisco products. If Cisco determines that
your insertion of non-Cisco memory, WIC cards, AIM cards,
Network Modules, SPA cards, GBICs or other modules into a
Cisco product is the cause of a support issue, Cisco may
deny support under your warranty or under a Cisco support
program such as SmartNet.
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 platform with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
