2960 switch down
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 12:30 PM
The L2 switch went down i.e all the end users had disconnected from the network, No network symbol.
After 5 minutes plugging and unplugging the uplink port the network came Up.
Don't know if it came up because of unplug and plugging uplink
and found only the below logs :
Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 5020 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 5020 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
File logging: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 5022 message lines logged
Logging Source-Interface: VRF Name:
Log Buffer (4096 bytes):
down
May 17 18:24:20.907: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to up
May 17 18:24:21.956: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to up
May 17 18:24:22.917: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to up
May 17 18:29:10.052: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to down
May 17 18:29:11.010: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to down
May 17 18:29:12.013: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to down
May 17 18:29:15.253: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to up
May 17 18:29:16.340: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to up
May 17 18:29:17.263: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to up
May 17 18:29:31.778: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to down
May 17 18:29:32.740: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to down
May 17 18:29:33.743: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to down
May 17 18:29:39.503: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to up
May 17 18:29:41.418: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to up
May 17 18:29:41.513: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to up
May 17 18:29:45.221: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to down
May 17 18:29:46.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to down
May 17 18:29:47.186: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to down
May 17 18:29:53.861: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed st ate to up
May 17 18:29:55.504: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, chan ged state to up
May 17 18:29:55.871: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet1/0/48, changed state to up
May 17 18:30:07.724: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
May 17 18:30:08.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to down
May 17 18:30:09.705: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to down
May 17 18:30:28.461: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to up
May 17 18:30:31.023: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to down
May 17 18:30:39.101: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to up
May 17 18:30:41.110: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to up
May 17 18:30:41.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
May 17 18:30:51.299: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
May 17 18:30:52.260: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to down
May 17 18:30:53.267: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to down
May 17 18:30:56.619: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to up
May 17 18:30:57.922: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
May 17 18:30:58.632: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to up
May 17 18:31:08.366: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
May 17 18:31:09.341: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to down
May 17 18:31:10.348: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to down
May 17 18:31:13.585: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/48, changed state to up
May 17 18:31:14.686: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
May 17 18:31:15.598: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/48, changed state to up
48th port is the trunk port to core switch.
cleared the interface counters and checked after that no CRC error Occured after that.
why the Interface vlan goes down ?
How can i troubleshoot this ?
How can i find route cause of this issue and prevent it from happening in future.
- Labels:
-
LAN Switching
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 12:45 PM
can you share
show spanning tree vlan X
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 12:47 PM
Was the switch rebooted? What is the output of "sh ver"?
HTH
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 03:10 PM
Any specific logs on the Core?
What is vlan 1 used for? Is it only part of int 48, if thats the case, port 48 going down will make vlan 1 down as well
Any layer 1 issue? Bad cable?
logs from other side can be helpful in this case
Raminder
PS: If this answered your question, please don't forget to rate and select as validated answer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 04:04 PM - edited 05-11-2022 04:08 PM
UP then down it may cause of STP Loop, so we need to see the
show spanning tree vlan x
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2022 04:50 PM
@jai.s401 wrote:
After 5 minutes plugging and unplugging the uplink port the network came Up.
<FACEPALM>
Post the complete output to the command "sh interface Gi1/0/48 controll".
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-12-2022 12:51 AM
I have attached the log of core switch #core and the switch which had a issue #switch 1"
according to the user the complaint is as below:
""one of the switches in got disconnected. When we observed physically the switch having power , all the ports are having green lights on , but devices not having traffic. After some time without any troubleshoot , all the devices got connected. ""
I have cleared the counters and after 10 hrs CRC errors observed in interfaces.
But when i run the TDR test, it shows the pair is normal. (attached in log)
please go through the log and guide me.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-12-2022 02:21 AM
@jai.s401 wrote:
I have cleared the counters and after 10 hrs CRC errors observed in interfaces.
That is not the output I have requested.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-14-2022 02:08 AM
I have included the logs that you have requested. If that doesn't help. please mention the specific command for required log.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-14-2022 02:25 AM
- Connect to your device (SSH) with : https://cway.cisco.com/cli/ . at the top left run or Press 'System Diagnostics' and also at the top right press 'Crashdump Analyzer'
M.
-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-17-2022 02:11 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-14-2022 03:28 AM
@jai.s401 wrote:
I have included the logs that you have requested. If that doesn't help. please mention the specific command for required log.
Last request: Post the complete output to the command "sh interface Gi1/0/48 controll".
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-14-2022 07:05 AM
Is the above command different one from " show interface Gi1/0/48 controller" ?????
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-17-2022 12:47 AM
Hi leo,
Here is the log required.
pls go through and give a root cause.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-17-2022 01:42 AM
@jai.s401 wrote:
800 FCS errors
Confirm this is a layer 1 issue.
