cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1220
Views
0
Helpful
4
Replies

3750 hangs after loading ios

zzbronski
Level 1
Level 1

Cisco 3750-48p, Loads ios ok and then all the checks pass test and then after "waiting for port download...complete" shows the device info as seen below and then hangs at that point.

File "flash:c3750-ipservicesk9-mz.122-55.SE10.bin" uncompressed and installed, entry point: 0x1000000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE10, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 11-Feb-15 11:40 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02F00000

Initializing flashfs...

flashfs[1]: 7 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 13357056
flashfs[1]: Bytes available: 2641920
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Checking for Bootloader upgrade.. not needed

POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed

POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed

POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed

POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed

Waiting for Stack Master Election...
POST: Inline Power Controller Tests : Begin
POST: Inline Power Controller Tests : End, Status Passed

POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed

POST: No Cable found on stack port 1
POST: No Cable found on stack port 2

POST: PortASIC Stack Port Loopback Tests : Begin
POST: PortASIC Stack Port Loopback Tests : End, Status Passed

POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed

Election Complete
Switch 1 booting as Master
Waiting for Port download...Complete


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C3750-48P (PowerPC405) processor (revision K0) with 131072K bytes of memory.
Processor board ID XXXXXXXXXXX
Last reset from power-on
1 Virtual Ethernet interface
48 FastEthernet interfaces
4 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : XXXXXXXXXXX
Motherboard assembly number     : 73-9675-11
Power supply part number        : 341-0029-05
Motherboard serial number       : XXXXXXXXXXX
Power supply serial number      : XXXXXXXXXXX
Model revision number           : K0
Motherboard revision number     : B0
Model number                    : WS-C3750-48PS-S
System serial number            : XXXXXXXXXXX
SFP Module assembly part number : 73-7757-03
SFP Module revision Number      : A0
SFP Module serial number        :
Top Assembly Part Number        :
Top Assembly Revision Number    : J0
Version ID                      : V05
CLEI Code Number                : COM1W00ARB
Hardware Board Revision Number  : 0x01


Switch Ports Model              SW Version            SW Image                 
------ ----- -----              ----------            ----------               
*    1 52    WS-C3750-48P       12.2(55)SE10          C3750-IPSERVICESK9-M     

4 Replies 4

Hello,

can you manually boot the switch (hold down to 'mode' button during the boot sequence and use the 'flash_init' and 'boot' commands) ?

I would give reformatting the flash a try and see if that makes a difference...

Yes, I am able able to get to recovery mode while holding the mode button on power up. I am able to read the flash with no issue. I thought maybe the IOS image was corrupted so I deleted and copied a newer version via xmodem. I booted with the new image and the same issue occurs where it hangs at the same point as above. Not sure what else I can do to troubleshoot. I suppose I can format the flash and see if that helps but then I have another 4 hour wait time to upload the image again.

Hello,

RMA is obviously the last option...

If you do a 'dir flash:' at the 'switch' prompt, are there any files in the directory that might look like they don't belong there ?

Before formatting the flash, if you decide to do that, run a consistency check with the 'fsck -test flash:' command...

I formatted the flash already. Doing the fsck flash: did not find any errors but did see a directory which I dont see listed. Copying the IOS image via xmodem again. Will be about 4.5 hours.

switch: fsck flash:
Are you sure you want to fsck "flash:" (could take some time) (y/n)?y
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 15997952
flashfs[0]: flashfs fsck took 9 seconds.

switch: dir flash:
Directory of flash:/


15997952 bytes available (1024 bytes used)

Review Cisco Networking for a $25 gift card