cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
726
Views
0
Helpful
2
Replies

6509 Module Failure

wajid dabir
Level 1
Level 1

I have two core switch in my network,HSRP is running between them.

My Primary Core switch 2 blades module are restarting.What can be the issue.

Find the attached logs.

CORE_SW_2#sh log

Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes,

0 overruns)

    Console logging: level debugging, 1024 messages logged

    Monitor logging: level debugging, 0 messages logged

    Buffer logging: level debugging, 1024 messages logged

    Exception Logging: size (4096 bytes)

    Count and timestamp logging messages: disabled

    Trap logging: level notifications, 487 message lines logged

        Logging to 10.1.46.74, 487 message lines logged

Log Buffer (8192 bytes):

1:14:37 IST: %STANDBY-6-STATECHANGE: Vlan54 Group 50 state Standby -> Active

.Feb  4 11:14:39 IST: %STANDBY-6-STATECHANGE: Vlan54 Group 50 state Active -> Sp

eak

.Feb  4 11:15:03 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:15:17 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Standby -> A

ctive

.Feb  4 11:15:19 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Active -> Sp

eak

.Feb  4 11:15:33 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:15:37 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Standby -> A

ctive

.Feb  4 11:15:46 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Active -> Sp

eak

.Feb  4 11:16:03 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:16:12 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Standby -> A

ctive

.Feb  4 11:16:15 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Active -> Sp

eak

.Feb  4 11:16:28 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Standby -> A

ctive

.Feb  4 11:16:28 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Active -> Sp

eak

.Feb  4 11:16:33 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:17:03 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:17:07 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Standby -> A

ctive

.Feb  4 11:17:10 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Active -> Sp

eak

.Feb  4 11:17:26 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Standby -> A

ctive

.Feb  4 11:17:28 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Active -> Sp

eak

.Feb  4 11:17:33 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:17:41 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Standby -> A

ctive

.Feb  4 11:17:41 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Active -> Sp

eak

.Feb  4 11:18:03 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:18:33 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:19:10 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:19:28 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Standby -> A

ctive

.Feb  4 11:19:28 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Active -> Sp

eak

.Feb  4 11:19:34 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Standby -> A

ctive

.Feb  4 11:19:34 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Active -> Sp

eak

.Feb  4 11:19:40 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:20:17 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:20:34 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Standby -> A

ctive

.Feb  4 11:20:36 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Active -> Sp

eak

.Feb  4 11:20:48 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Standby -> A

ctive

.Feb  4 11:20:48 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Active -> Sp

eak

.Feb  4 11:21:01 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:21:24 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Standby -> A

ctive

.Feb  4 11:21:25 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Active -> Sp

eak

.Feb  4 11:21:33 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:21:41 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Standby -> A

ctive

.Feb  4 11:21:41 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Active -> Sp

eak

.Feb  4 11:21:41 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Standby -> A

ctive

.Feb  4 11:21:41 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Active -> Sp

eak

.Feb  4 11:21:43 IST: %STANDBY-6-STATECHANGE: Vlan49 Group 50 state Standby -> A

ctive

.Feb  4 11:21:45 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Standby -> A

ctive

.Feb  4 11:21:45 IST: %STANDBY-6-STATECHANGE: Vlan49 Group 50 state Active -> Sp

eak

.Feb  4 11:21:50 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Standby -> A

ctive

.Feb  4 11:21:52 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Active -> Sp

eak

.Feb  4 11:21:54 IST: %STANDBY-6-STATECHANGE: Vlan55 Group 50 state Active -> Sp

eak

.Feb  4 11:22:03 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:22:05 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Standby -> A

ctive

.Feb  4 11:22:06 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Active -> Sp

eak

.Feb  4 11:22:38 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:23:04 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Standby -> A

ctive

.Feb  4 11:23:08 IST: %STANDBY-3-DUPADDR: Duplicate address 10.1.47.4 on Vlan47,

sourced by 0019.0784.b400

.Feb  4 11:23:15 IST: %STANDBY-6-STATECHANGE: Vlan53 Group 50 state Active -> Sp

eak

.Feb  4 11:23:18 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Standby -> A

ctive

.Feb  4 11:23:20 IST: %STANDBY-6-STATECHANGE: Vlan50 Group 50 state Active -> Sp

eak

.Feb  4 11:23:22 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Standby -> A

ctive

.Feb  4 11:23:24 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Standby -> A

ctive

.Feb  4 11:23:24 IST: %STANDBY-6-STATECHANGE: Vlan52 Group 50 state Active -> Sp

eak

.Feb  4 11:23:25 IST: %STANDBY-6-STATECHANGE: Vlan48 Group 50 state Active -> Sp

eak

Feb  9 15:30:48 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb  9 15:31:10 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb  9 15:31:19 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb  9 15:31:18 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb  9 15:31:20 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Feb 11 23:51:37 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb 11 23:51:59 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb 11 23:52:07 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb 11 23:52:07 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb 11 23:52:09 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Feb 11 23:58:15 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb 11 23:58:37 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb 11 23:58:46 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb 11 23:58:45 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb 11 23:58:47 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Feb 17 13:19:49 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb 17 13:21:07 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb 17 13:21:15 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb 17 13:21:15 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb 17 13:21:17 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Feb 17 17:54:47 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb 17 17:55:55 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb 17 17:56:03 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb 17 17:56:03 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb 17 17:56:05 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Feb 17 22:26:01 IST: %OIR-SP-6-REMCARD: Card removed from slot 2, interfaces dis

abled

Feb 17 22:39:43 IST: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimum Diagnosti

cs...

.Feb 17 22:39:51 IST: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been

disabled.

Feb 17 22:39:51 IST: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Feb 17 22:39:52 IST: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are

now online

Regards,

Wajid Dabir

1 Accepted Solution

Accepted Solutions

Jose Solano
Level 4
Level 4

Hi,

As per the outputs looks like the module 2 is getting reset for no apparent reason. The logs showed the system resets the power for module 2 and it comes back in a while with clean diagnostic results. This can be an issue with the module itself, the slot in the chassis or it could be that the module is not seated properly or there is dust in the module and backplane contact. In this case, I would say that you can try reseating the module, try swapping the module with a module in any other slot working fine. This will help you to isolate the issue further and see if it is hardware related.

Hope this helps.

View solution in original post

2 Replies 2

Jose Solano
Level 4
Level 4

Hi,

As per the outputs looks like the module 2 is getting reset for no apparent reason. The logs showed the system resets the power for module 2 and it comes back in a while with clean diagnostic results. This can be an issue with the module itself, the slot in the chassis or it could be that the module is not seated properly or there is dust in the module and backplane contact. In this case, I would say that you can try reseating the module, try swapping the module with a module in any other slot working fine. This will help you to isolate the issue further and see if it is hardware related.

Hope this helps.

Dear jose,

I done the testing whatever you suggested, finally we come to know that module is faullty.

Review Cisco Networking for a $25 gift card