08-10-2015 07:50 AM - edited 03-08-2019 01:18 AM
Hi,
We have a directly connected 1 giga Ethernet link between 7600 ES+ 20xGE SFP/Cisco 7606-s port and a Cisco 3560, we have tried all combination of duplex and speed settings cat5/6 cable change; but we are getting packet loss, please advise where could be the problem ?
New_Router_7600#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAB103400Y1
2 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAB1034046Z
3 0 2 port adapter Enhanced FlexWAN WS-X6582-2PA JAE1010XAZF
4 20 7600 ES+ 7600-ES+20G3CXL JAE1340KH0U
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE JAE1405388I
6 2 Route Switch Processor 720 (Hot) RSP720-3CXL-GE SAL16052QWF
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ----- ------------- ------------ -------
1 0019.0699.da94 to 0019.0699.db13 2.3 Unknown Unknown PwrDown
2 0019.0699.d114 to 0019.0699.d193 2.3 Unknown Unknown PwrDown
3 0016.c827.d8e0 to 0016.c827.d91f 2.2 Unknown Unknown PwrDown
4 1cdf.0fa3.3860 to 1cdf.0fa3.389f 1.3 12.2(33r)SRD 15.3(3)S Ok
5 001c.584f.1770 to 001c.584f.1773 5.9 12.2(33r)SRD 15.3(3)S Ok
6 0022.bdeb.80f0 to 0022.bdeb.80f3 5.13 12.2(33r)SR 15.3(3)S Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
4 7600 ES+ DFC XL 7600-ES+3CXL JAE14420TE8 1.1 Ok
4 7600 ES+ 20xGE SFP 7600-ES+20G JAE14420SBT 1.1 Ok
5 Policy Feature Card 3 7600-PFC3CXL JAE14053867 1.1 Ok
5 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE14052VSK 1.5 Ok
6 Policy Feature Card 3 7600-PFC3CXL SAL16020L3U 1.1 Ok
6 C7600 MSFC4 Daughterboard 7600-MSFC4 SAL16063GXX 5.0 Ok
Mod Online Diag Status
---- -------------------
1 Not Applicable
2 Not Applicable
3 Not Applicable
4 Pass
5 Pass
6 Pass
---------------------------------------------------------------------------------
router 7600:
New_Router_Core_7600#sh int gi4/11
GigabitEthernet4/11 is up, line protocol is up (connected)
Hardware is X40G 1Gb 802.3, address is 6c41.6a26.f680 (bia 6c41.6a26.f680)
Internet address is 2.2.2.1/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, clock source internal, media type is T
input flow-control is off, output flow-control is on
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:44, output 00:00:50, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 207725 pkt, 209829313 bytes - mcast: 784 pkt, 95112 bytes
L3 in Switched: ucast: 975 pkt, 341306 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
16210406 packets input, 2397855914 bytes, 0 no buffer
Received 53120 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
204791 packets output, 209675529 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
switch 3560:
cs.ca1.net#sh int GigabitEthernet0/48
GigabitEthernet0/48 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 1c17.d324.ffe2 (bia 1c17.d324.ffe2)
Internet address is 2.2.2.2/30
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:52, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
204759 packets input, 209667087 bytes, 0 no buffer
Received 290 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 285 multicast, 0 pause input
0 input packets with dribble condition detected
16209321 packets output, 2397488447 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
---------------------------------------------------------------------------------------------
cs.ca1.net#ping 2.2.2.1 repeat 1000
Type escape sequence to abort.
Sending 1000, 100-byte ICMP Echos to 2.2.2.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!.!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!..!!!!!!!!.!!!!!.!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!
Success rate is 99 percent (993/1000), round-trip min/avg/max = 1/2/17 ms
best regard.
Benchabane Mohamed
08-11-2015 04:45 AM
Hello Mohamed
Do you have control-plane protection enabled on your 7600-series router?
Have a look at show policy-map control-plane on your 7600 to see if you have any pings denied by CoPP.
Best regards,
Martin
08-13-2015 01:50 AM
Hello Martin;
first thanks for your replay;
I did a show policy-map control-plane but i haven't any result
New_Router_Core_CA1_ALG#show policy-map control-plane
New_Router_Core_CA1_ALG#
how can I enable control-plane protection ? or have you any other suggestion ?
best regard.
Benchabane Mohamed.
08-13-2015 06:00 AM
Hi Mohamed
I was just wondering whether you configured any policy there, because with control-plane protection you can limit inbound traffic like pings to prevent them from overrunning your device. So if the rate of incoming ICMP echo-requests exceeds a predefined threshold, you start dropping.
Here's a link with configuration details: http://www.cisco.com/c/en/us/td/docs/routers/7600/ios/15S/configuration/guide/7600_15_0s_book/dos.pdf
On some platforms it's enabled by default, on yours it's apparently not.
Do you have any QoS implemented on the link between the 7600 and the 3560? Something that would rate-limit traffic, or drop packets in case of congestion?
What happens when you try to send 500 pings at a time, then wait for a few seconds and then repeat? Do you still get drops?
Best regards,
Martin
08-13-2015 07:04 AM
Hi Martin,
We don't have any QoS implemented on the link between the 7600 and the 3560, we have tried to send 500 pings at a time and wait and send others but we are getting a random packet loss, some times there is some packet loss some other time not. as you can notice on the below output:
New_Router_Core_CA1_ALG#ping 10.20.0.104 repeat 500 size 1500
Type escape sequence to abort.
Sending 500, 1500-byte ICMP Echos to 10.20.0.104, timeout is 2 seconds:
!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!
Success rate is 99 percent (499/500), round-trip min/avg/max = 1/1/20 ms
New_Router_Core_CA1_ALG#ping 10.20.0.104 repeat 500 size 1500
Type escape sequence to abort.
Sending 500, 1500-byte ICMP Echos to 10.20.0.104, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!
Success rate is 100 percent (500/500), round-trip min/avg/max = 1/1/4 ms
New_Router_Core_CA1_ALG#ping 10.20.0.104 repeat 500 size 1500
Type escape sequence to abort.
Sending 500, 1500-byte ICMP Echos to 10.20.0.104, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!
Success rate is 99 percent (499/500), round-trip min/avg/max = 1/1/8 ms
We had some doubt about the cisco 3560 switch, so we added a new link with another 4948 switch and have done some simultaneous pings tests to both 3560 and 4948 SW and we were very surprised that the packet loss occured at the same time ! do you any clue, thanks for your help
Best regards,
Mohamed
08-16-2015 05:20 AM
Hi Martin,
Do you have any ideas or recommendations or any suggestions please ?
Best Regards,
Mohamed.
08-17-2015 12:01 AM
Hello Mohamed
Would it be possible for you to post an output of show running-config from the 7600?
Best regards,
Martin
08-17-2015 08:46 AM
Hi Martin;
so happy to hear about you
here is the show run:
-------------------------------------------------
New_Router_Core_CA1_ALG#sh run
Building configuration...
Current configuration : 41555 bytes
!
! Last configuration change at 12:49:36 ALG Mon Aug 17 2015 by benchabane
! NVRAM config last updated at 13:12:40 ALG Mon Aug 17 2015 by benchabane
!
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
service counters max age 10
no service image-version efsu
!
hostname New_Router_Core_CA1_ALG
!
boot-start-marker
boot system bootdisk:c7600rsp72043-adventerprisek9-mz.153-3.S2.bin
boot system flash sup-bootdisk:c7600rsp72043-ipservicesk9-mz.152-4.S6.bin
boot-end-marker
!
!
logging buffered 16000
no logging console
no logging monitor
!
no aaa new-model
!
!
!
clock timezone ALG 1 0
!
ip domain retry 1
ip domain timeout 2
ip name-server x.x.x.x
ip name-server x.x.x.x
ip name-server 8.8.8.8
!
!
!
!
l2tp-class l2-dyn
authentication
password 7 020F5C48145B73
cookie size 8
!
no mpls ldp advertise-labels
mpls ldp advertise-labels for LP-MPLS
mls flow ip interface-full
no mls flow ipv6
mls cef error action reset
multilink bundle-name authenticated
!
!
!
!
archive
log config
logging enable
logging size 500
notify syslog contenttype plaintext
hidekeys
spanning-tree mode pvst
spanning-tree extend system-id
!
no power enable module 2
no power enable module 3
diagnostic bootup level minimal
!
redundancy
main-cpu
auto-sync running-config
mode sso
!
!
!
!
vlan internal allocation policy ascending
vlan access-log ratelimit 2000
!
ip ssh version 2
!
!
track 1 ip sla 1 reachability
!
track 2 ip sla 2 reachability
!
track 3 ip sla 3 reachability
!
track 4 ip sla 4 reachability
!
track 5 ip sla 5 reachability
!
track 6 ip sla 6 reachability
!
track 7 ip sla 7 reachability
!
track 8 ip sla 8 reachability
!
track 19 ip sla 19 reachability
!
!
class-map match-all toto
match any
class-map match-all 2class
match any
pseudowire-class pw-dynamic
encapsulation l2tpv3
protocol l2tpv3 l2-dyn
ip local interface Loopback220
!
!
!
!
!
!
!
!
!
!
!
interface Loopback0
description used for management
ip address 172.31.1.121 255.255.255.255
ip ospf 1 area 1
!
interface Loopback1
no ip address
!
interface Loopback220
ip address 192.168.220.1 255.255.255.255
!
interface POS1/0/0
no ip address
shutdown
!
interface POS1/0/1
no ip address
shutdown
!
interface POS1/0/2
no ip address
shutdown
!
interface POS1/0/3
no ip address
shutdown
!
interface POS1/1/0
no ip address
shutdown
!
interface POS1/1/1
no ip address
shutdown
!
interface POS1/1/2
no ip address
shutdown
!
interface POS1/1/3
no ip address
shutdown
!
interface POS1/1/4
no ip address
shutdown
!
interface POS1/1/5
no ip address
shutdown
!
interface POS1/1/6
no ip address
shutdown
!
interface POS1/1/7
no ip address
shutdown
!
interface GigabitEthernet4/1
mtu 3000
ip address x.x.x.x 255.255.255.248
ip router isis
ip ospf 1 area 0
speed 1000
mpls ip
isis network point-to-point
!
interface GigabitEthernet4/2
ip address x.x.x.x 255.255.255.248
ip router isis
ip ospf 1 area 0
speed auto
mpls ip
isis network point-to-point
!
interface GigabitEthernet4/3
no ip address
speed 1000
!
interface GigabitEthernet4/4
no ip address
shutdown
!
interface GigabitEthernet4/5
no ip address
shutdown
!
interface GigabitEthernet4/6
no ip address
shutdown
!
interface GigabitEthernet4/7
no ip address
shutdown
!
interface GigabitEthernet4/8
no ip address
shutdown
!
interface GigabitEthernet4/9
no ip address
ip ospf 1 area 1
speed 1000
!
interface GigabitEthernet4/9.1
encapsulation dot1Q 1 native
ip address x.x.x.x 255.255.255.0
ip policy route-map Tlemcen_to_Mad_London
ip ospf 1 area 1
!
interface GigabitEthernet4/9.13
encapsulation dot1Q 13
ip address 172.31.1.233 255.255.255.252
!
interface GigabitEthernet4/9.14
encapsulation dot1Q 14
ip address x.x.x.x 255.255.255.224
!
interface GigabitEthernet4/9.15
encapsulation dot1Q 15
ip address 172.31.1.94 255.255.255.240
!
interface GigabitEthernet4/9.134
encapsulation dot1Q 134
ip address 172.31.1.54 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.135
encapsulation dot1Q 135
ip address 172.31.1.78 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.136
encapsulation dot1Q 136
ip address 172.31.1.158 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.502
encapsulation dot1Q 502
ip address x.x.x.x 255.255.255.240
ip ospf 1 area 1
!
interface GigabitEthernet4/9.509
encapsulation dot1Q 509
ip address 172.31.1.6 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.511
encapsulation dot1Q 511
ip address 172.31.1.38 255.255.255.248
ip router isis
ip ospf 1 area 1
mpls ip
!
interface GigabitEthernet4/9.516
encapsulation dot1Q 516
ip address 172.31.1.14 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.517
encapsulation dot1Q 517
ip address 172.31.1.70 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.518
encapsulation dot1Q 518
ip address 172.31.1.22 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.519
encapsulation dot1Q 519
ip address 172.31.1.198 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.523
encapsulation dot1Q 523
ip address 172.31.1.46 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.524
encapsulation dot1Q 524
ip address 172.31.1.62 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.525
encapsulation dot1Q 525
ip address 172.31.1.150 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.526
bandwidth 1000000
encapsulation dot1Q 526
ip address 172.31.1.101 255.255.255.248
ip ospf 1 area 1
ip ospf cost 30
!
interface GigabitEthernet4/9.610
encapsulation dot1Q 610
ip address 172.31.1.30 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.615
encapsulation dot1Q 615
ip address 172.31.1.129 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/9.700
encapsulation dot1Q 700
ip address 172.31.1.225 255.255.255.248
ip ospf 1 area 1
!
interface GigabitEthernet4/10
ip address 10.12.13.1 255.255.255.0
!
interface GigabitEthernet4/11
ip address 2.2.2.1 255.255.255.252
speed 1000
!
interface GigabitEthernet4/12
no ip address
shutdown
!
interface GigabitEthernet4/13
no ip address
shutdown
!
interface GigabitEthernet4/14
no ip address
shutdown
!
interface GigabitEthernet4/15
no ip address
shutdown
!
interface GigabitEthernet4/16
no ip address
shutdown
!
interface GigabitEthernet4/17
no ip address
shutdown
!
interface GigabitEthernet4/18
no ip address
shutdown
!
interface GigabitEthernet4/19
no ip address
shutdown
!
interface GigabitEthernet4/20
no ip address
shutdown
!
interface GigabitEthernet5/1
no ip address
shutdown
!
interface GigabitEthernet5/2
ip address 5.5.5.1 255.255.255.0
media-type rj45
speed 1000
duplex full
!
interface GigabitEthernet6/1
no ip address
shutdown
!
interface GigabitEthernet6/2
no ip address
shutdown
!
interface Vlan1
no ip address
shutdown
!
!
router eigrp 220
network 172.16.44.18 0.0.0.0
network 172.31.1.38 0.0.0.0
distance eigrp 254 254
distance 255 0.0.0.0 255.255.255.255 Not-MPLS-LP
!
router ospf 1
router-id 1.1.1.1
area 1 nssa no-redistribution no-summary
redistribute static metric-type 1 subnets route-map Redistrib_Static
!
router isis
net 49.0001.4444.4444.4444.00
metric-style wide
!
router bgp 36891
bgp log-neighbor-changes
no bgp default ipv4-unicast
neighbor 192.168.220.2 remote-as 36891
neighbor 192.168.220.2 update-source Loopback220
neighbor 192.168.220.3 remote-as 36891
neighbor 192.168.220.3 update-source Loopback220
neighbor 192.168.220.4 remote-as 36891
neighbor 192.168.220.4 update-source Loopback220
!
address-family ipv4
exit-address-family
!
address-family vpnv4
neighbor 192.168.220.2 activate
neighbor 192.168.220.2 send-community both
neighbor 192.168.220.2 route-reflector-client
neighbor 192.168.220.3 activate
neighbor 192.168.220.3 send-community both
neighbor 192.168.220.3 route-reflector-client
neighbor 192.168.220.4 activate
neighbor 192.168.220.4 send-community both
neighbor 192.168.220.4 route-reflector-client
exit-address-family
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
!
ip prefix-list Def_Only seq 5 permit 0.0.0.0/0
ip sla 1
icmp-echo x.x.x.x source-interface GigabitEthernet4/1
ip sla schedule 1 life forever start-time now
ip sla 3
icmp-echo x.x.x.x
timeout 20000
ip sla schedule 3 life forever start-time now
ip sla 4
icmp-echo x.x.x.x
ip sla schedule 4 life forever start-time now
ip sla 5
icmp-echo x.x.x.x
ip sla schedule 5 life forever start-time now
ip sla 6
icmp-echo x.x.x.x
ip sla schedule 6 life forever start-time now
ip sla 7
icmp-echo x.x.x.x
ip sla schedule 7 life forever start-time now
ip sla 8
icmp-echo x.x.x.x
ip sla schedule 8 life forever start-time now
ip sla 9
icmp-echo x.x.x.x
ip sla 19
icmp-echo x.x.x.x
ip sla schedule 19 life forever start-time now
logging alarm informational
logging trap notifications
!
route-map Redistrib_Static permit 10
match ip address Redistrib_Static
!
route-map Redistrib_Static deny 20
!
route-map Def_Only permit 10
match ip address prefix-list Def_Only
!
route-map Tlemcen_to_London permit 10
match ip address Tlemcen_to_Mad_London
set ip next-hop x.x.x.x
!
mpls ldp router-id Loopback220 force
!
!
control-plane
!
line con 0
logging synchronous
login local
stopbits 1
line vty 0 4
logging synchronous
login local
transport input telnet ssh
!
exception crashinfo buffersize 80
ntp source GigabitEthernet4/9
ntp update-calendar
ntp server x.x.x.x
ntp server x.x.x.x
!
!
end
-------------------------------------------
ther is a lot of static route that i didn't post in the show
best regard
Mohamed.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide