04-18-2018
06:58 AM
- last edited on
03-25-2019
04:47 PM
by
ciscomoderator
I have couple of ISR 4331 and I need to activate the appxk9 license.
I can see this from slow license output:
Router6#sh license
Index 1 Feature: appxk9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
How can I activate the license? Will it expire and loose the functionalities when it expires?
Thank you in advance.
Solved! Go to Solution.
04-18-2018 05:06 PM
Hi
The command would be license right-to-use LicenseName
You can take a look on that thread (https://supportforums.cisco.com/t5/lan-switching-and-routing/help-with-isr4331-evaluation-license/td-p/3178071) where this question has been answered.
04-18-2018 05:06 PM
Hi
The command would be license right-to-use LicenseName
You can take a look on that thread (https://supportforums.cisco.com/t5/lan-switching-and-routing/help-with-isr4331-evaluation-license/td-p/3178071) where this question has been answered.
04-18-2018 11:03 PM
Hi Francesco,
Does this license run out? Is it just active for a certain period and then stops working?
Regards.
04-19-2018 05:10 AM
04-26-2018 08:27 AM
Thank you Francesco!
04-26-2018 06:56 PM
10-08-2018 04:04 AM
But for a 4321 :
Sh license
Index 1 Feature: appxk9
Period left: Life time
License Type: RightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
Are you sure it will run out??
10-08-2018 01:21 PM
10-09-2018 05:58 AM
Thank your for your reply and I suppose it's the same for securityk9 since it's giving me the same output:
Index 3 Feature: securityk9
Period left: Life time
License Type: RightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
10-09-2018 07:10 PM
10-02-2019 03:11 AM
Hi,
Similar issue, hope you can help.
I have purchased a appxk9 licence, I received a zip file from eDelivery which contains three pdf files.
My question is, what are the next steps to get this actually installed an working?
At the moment my router shows:
rtr-lon-01#sh license
Index 1 Feature: appxk9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
show ver
Cisco IOS XE Software, Version 16.05.01b
Cisco IOS Software [Everest], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.5.1b, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Tue 11-Apr-17 16:39 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2017 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
System image file is "bootflash:isr4300-universalk9.16.05.01b.SPA.bin"
Thanks for your help.
10-06-2019 08:03 PM
10-07-2019 08:58 AM
Hi Francesco,
It was a little more convoluted than that. I received an email from cisco support which I am still trying to understand:#
"
I have put the license from SO: under a PAK: FP5LI9R4YZM and have fulfilled it to PID: ISR4331/K9 SN: FDO21160JPU.
You should have received an e-mail from do-not-reply@cisco.com with the license file and I am also attaching it here.
Once you receive a PAK you should fulfill it to a device using the steps below, however you can also always open a chat with us or a case, however chats are faster for PAK fulfillment.
Clear and simple no?
Now that have the .lic file I think I can follow the instructions described in the link you have sent.
10-10-2019 06:47 PM
10-11-2019 01:37 AM
Yes, that is it.
The Cisco license team did that for me and here are the summary instructions after that:
1) Unzip the .zip file you received
2) Copy the .lic file within this to the router's bootflash
3) From the router console, issue "license install bootflash:<name of
file>.lic" where "<name of file>" is the name of the license file.
And that was it; no EULA to accept, no reload needed
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide