11-14-2012 05:15 AM - edited 03-07-2019 10:02 AM
hi
i understand that you cant create vlan subinterface on 3750 or 3550
switch(config)#int gi1/0/52.100
^
% Invalid input detected at '^' marker.
Is there any alternative to create the above (by upgrading to latest ios?). basically i have a trunk port with SVI interfaces but i would like to spilit the trunk into sub interfaces and have it on its own vlan AND have the layer 3 ip for some (like below)
switch(config)#int gi1/0/52.100
switch(config-if)# switch access vlan 100
switch(config)#int gi1/0/52.200
switch(config-if)# switch access vlan 200
switch(config)#int gi1/0/52.300
switch(config-if)# no switchport
switch(config-if)# ip address 10.10.30.1 255.255.255.0
int vlan 100
ip address 10.10.100.1 255.255.255.0
int vlan 200
ip address 10.10.200.1 255.255.255.0
is the above possible ?
thanks
11-14-2012 05:29 AM
Hi,
What is your purpose for that? What do you want to reach?
For such thing you need router in order to create subinterfaces.
Hope it will help
11-14-2012 06:19 AM
i would like to spilit my vlans for troubleshooting. for instance i can just shutdown just 1 vlan instead of shutting down the entire trunk port ?
11-14-2012 06:41 AM
You can shut down a vlan from vlan config mode without going through this. I've never done it, but it sounds like this is what you're wanting.
DR_Switch(config)#vlan 282
DR_Switch(config-vlan)#?
VLAN configuration commands:
are Maximum number of All Route Explorer hops for this VLAN (or
zero if none specified)
backupcrf Backup CRF mode of the VLAN
bridge Bridging characteristics of the VLAN
exit Apply changes, bump revision number, and exit mode
media Media type of the VLAN
mtu VLAN Maximum Transmission Unit
name Ascii name of the VLAN
no Negate a command or set its defaults
parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs
private-vlan Configure a private VLAN
remote-span Configure as Remote SPAN VLAN
ring Ring number of FDDI or Token Ring type VLANs
said IEEE 802.10 SAID
shutdown Shutdown VLAN switching
state Operational state of the VLAN
HTH,
John
11-14-2012 07:30 PM
Unfortunately you cannot do that on a switch. Instead, you have to run a trunk and a bunch of SVIs, as you have done.
Unfortunately, if you are running any routing protocols through the trunk, and the trunk link fails, then the re-convergence is slower because it has to rely on dead times rather than detecting link-down.
Kevin Dorrell
Luxembourg
11-16-2012 03:22 AM
say if i introduce to bring in a router and do
on router:
int fa0/0.20
encapsulation dot1q 20
ip address 192.168.2.254 255.255.255.0
no shut
int fa0/0.30
encapsulation dot1q 30
ip address 192.168.3.254 255.255.255.0
no shut
on the switch:
vlan database
vlan 20 name 20
vlan 30 name 30
int vlan 20
ip address 192.168.2.200 255.255.255.0
no shut
int vlan 30
ip address 192.168.3.200 255.255.255.0
no shut
I know the above will work for L2 vlans but for Layer 3 (without any vlans will the below config do ?)
int fa0/0.40
ip address 192.168.4.1 255.255.255.0
no shut
int fa0/0.50
ip address 192.168.5.1 255.255.255.0
no shut
on switch side (different switch to the one above)
int fa0/1
ip add 192.168.4.2 255.255.255.0
no shut
int fa0/2
ip add 192.168.5.2 255.255.255.0
no shut
Basically my question is if i replace the l3 switch with a router can i use one port for L2 sub interface and another port for L3 sub interface as above ?
if so how do i create a layer 3 sub interface ?
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide