09-26-2011 04:01 AM - edited 03-07-2019 02:26 AM
Hi,
I tried to get my macros running by a remote server.
This is my remote function file named "remote_test_pc.asp":
if [[ $LINKUP -eq YES ]]; then
conf t
interface $INTERFACE
macro description $TRIGGER
description PC-VoIP-Port
switchport access vlan $ACCESS_VLAN
switchport mode access
switchport voice vlan $VOICE_VLAN
storm-control broadcast level pps 1k
storm-control multicast level pps 2k
storm-control action trap
no logging event link-status
srr-queue bandwidth share 10 10 5 75
srr-queue bandwidth shape 10 0 0 0
priority-queue out
mls qos trust dscp
no snmp trap link-status
spanning-tree portfast
spanning-tree bpduguard enable
service-policy input PO_TRUST-PHONE
exit
end
fi
if [[ $LINKUP -eq NO ]]; then
conf t
interface $INTERFACE
no macro description
description DEFAULT-CONFIG
switchport mode access
switchport access vlan 999
storm-control broadcast level pps 1k
storm-control multicast level pps 2k
storm-control action trap
spanning-tree portfast
no switchport voice vlan $VOICE_VLAN
srr-queue bandwidth share 10 10 5 75
srr-queue bandwidth shape 10 0 0 0
priority-queue out
mls qos trust dscp
no service-policy input PO_TRUST-PHONE
fi
exit
end
fi
And this is my config on the switch for mac-group and macro:
!
macro auto mac-address-group Test-PC
mac-address list 0019.9990.5509
!
macro auto global processing
macro auto global control detection mac-address
!
macro auto execute Test-PC remote ftp://192.168.1.11/remote_test_pc.asp ACCESS_VLAN=123 VOICE_VLAN=127
!
When I plug this workstation to the following syslog messages:
Switch#
Loading remote_test_pc.asp !
[OK - 1702/4096 bytes]
Enter configuration commands, one per line. End with CNTL/Z.
Switch con0 is now available
Press RETURN to get started.
Error: Failed to execute trigger Test-PC, please verify trigger exists and maps to valid function
Sep 26 11:45:37.755: %SYS-5-CONFIG_I: Configured from console by console
Sep 26 11:45:37.772: %AUTOSMARTPORT-5-INSERT: Message from tty0(user id: ): Device with mac-address 0019.9990.5509 detected on interface FastEthernet0/3, executed Test-PC
Switch#
The port is working as it should, but I am wondering about the error message.
Switch is 2960 with IOS 12.2(58)SE2.
Can anybody explain what that means?
Thanks a lot!
Sven
Solved! Go to Solution.
09-26-2011 05:18 AM
Hi Sven,
I believe you won't be getting this message consistently...Ignore this for now...This won't have any functional impact...This was taken care in 15.0(1)SE.
Thanks,
-Ankur
09-26-2011 05:18 AM
Hi Sven,
I believe you won't be getting this message consistently...Ignore this for now...This won't have any functional impact...This was taken care in 15.0(1)SE.
Thanks,
-Ankur
09-26-2011 05:28 AM
Hi Ankur,
I did a lot of tests (> 20 times of link up/down) and evertime I get that error message.
But okay, if it is not important I will ignore it .
Later I will do some tests with 15.0(1)SE.
Thanks!
Sven
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: