C1000 switch PACL MAC filtering not working

[para35]

Hello, 

I have got a C1000 switch. iOS is 15.2(7)E6.

I am trying a MAC address filtering to the ports.

1. (config) mac access-list extended <named list>

2. (config-ext-macl) permit host <MAC address> any

3 (config-ext-macl) deny any any

4. (config) int range gig 1/0/1-24 

5.  (config-if-range) mac access-group <named list> in

do wr.

So I have got a permitted MAC address in the list, but if I plug a new Laptop it got connection, IP address, everything.

So the Deny any any is not working.

I should use the mac 'access-group <named list> out' command, but out option is not in the commands.

What can be the solution to bloc the other Laptops which are not on my MAC Access list?

I am waiting your advice.

Thank you.

Kind regards, 

Para35

[MHM Cisco World]

https://ine.com/blog/an-introduction-to-mac-access-lists

check this link, 
you need to permit/deny ARP 
the MAC can not filter packet with IP header 

Thanks A Lot
MHM

[para35]

Hello, 

What is the reason the deny any any in this case?  This list is not blocking the port with the MAC address which is not consist of the extended list?

So if my goal is to make a full list with 5 EA Laptop MAC addresses which is permitted, but all of other should be block if they  MAC addresses is not part of the list. I can do it with PACL or I have to use the Port security instead?

THX

[MHM Cisco World]

sure port security with static mac is better solution here.

switchport port-security mac-address MAC_address 

note:- the IP guard need dhcp snooping in all sw.

Thanks A Lot
MHM

[para35]

Thanks, for the answer.

In this case what is the purpose this MAC address filtering, if I cannot deny any any, and approved just my 5 LAPtop MAC Address?

What will be the result to my config? The Laptop6 shouldn't be blocked? 

1. (config) mac access-list extended <named list>

2. (config-ext-macl) permit host <MAC address> any

3 (config-ext-macl) deny any any

4. (config) int range gig 1/0/1-24 

5.  (config-if-range) mac access-group <named list> in

Thanks 

[MHM Cisco World]

it not work, all traffic will deny even the traffic from permit mac address.
as I mention before the MAC list not filter IP packet. 

try port security instead it simple and safe.

[para35]

But If I plug the Laptop6 it is connected and get network, everything. (I believed with deny any any, it will not get anything.)

So basically all of traffic is just going.

[MHM Cisco World]

As I mention use port secuirty.

Mac acl with IP packet and arp is not work as we need.

Thanks A Lot
MHM

[Gopinath_Pigili]

From the IOS Configuration Guide for 12.2SXF at

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/acl.html#wp1081810

Each type of ACL (IP, IPX, and MAC) filters only traffic of the corresponding type. A Cisco IOS MAC ACL never matches IP or IPX traffic.

Filtering IP traffic using MAC ACLs will therefore not be possible. Probably by using the IP Source Guard with source MAC verification could solve your problem.

Best regards
******* If This Helps, Please Rate *******

[para35]

Hello, 

I just don't want to shutdown the ports, but be sure just that 5 laptops can be connected by MAC-addresses to the switch.

If I have to plug the the Laptop1 from port 1 to port 20 should be connected because of the MAC addresses allowed in the list. And if I plug Laptop6 it should be not connected/forbidden according to the MAC address list.

I don't want to filter the IP.

Do I have to use other solutions?

THX

[Gopinath_Pigili]

it is not going to work in that way....I think....additionaly...you should configure access-map and vlan filter....

Here are the stpes: 

1) Create mac-acl

2) Create access-map in that link mac-acl

3) Apply vlan filter command with access-map

Here is the sample configuration:

Catalyst(config)# mac access-list extended M-ARP
　Catalyst(config-ext-macl)# permit host 1234.5678.1234 host 1234.5678.abcd 0x0806 0x0

　Catalyst(config)# vlan access-map V-MAP 10
　Catalyst(config-access-map)# match mac-address M-ARP
　Catalyst(config-access-map)# action forward

　Catalyst(config)# vlan access-map V-MAP 20
　Catalyst(config-access-map)# action drop

　Catalyst(config)# vlan filter V-MAP vlan-list 30

Best regards
******* If This Helps, Please Rate *******