02-17-2019 07:48 AM - edited 03-08-2019 05:21 PM
Hi All,
Met with a strange behaviour today,
we have 2x C6880X and IAs etherchanneled to either core.
When the VSL is unplugged, the core and IAs will reboot and fail to restore connection.
VSS is on (show switch virtual link)
Could really use some help here, thanks a lot!
02-17-2019 09:55 AM
Depends how you have configuered, explain more how the setup and topology and show run config of both the devices.
02-17-2019 11:39 PM
The setup is normal:
Two 6880 with 2x physical links in 2 portchannels
IAs are connected with 2x physical links (portchannel), one link each to each 6880
UPDATE:
I noticed that Fast Hello is enabled but I do not have a third physical link for it.
So is it normal behaviour for the Cores and IAs to reload when VSL breaks in this case?
I did read about the split brain scenario
Related VSS show run:
boot system bootdisk:c6880x-ipservicesk9-mz.SPA.151-2.SY6.bin
fex 112
description FEX0112
fex 113
description FEX0113
fex 144
description FEX0144
fex 152
description FEX0152
fex 153
description FEX0153
fex 163
description FEX0163
fex 170
description FEX0170
fex 174
description FEX0174
fex 182
description FEX0182
fex 192
description FEX0192
fex 194
description FEX0194
fex 195
description FEX0195
fex 196
description FEX0196
!
switch virtual domain 1
switch mode virtual
switch 1 priority 200
mac-address use-virtual
redundancy
main-cpu
auto-sync running-config
mode sso
interface Port-channel1
no switchport
no ip address
no platform qos channel-consistency
switch virtual link 1
interface TenGigabitEthernet1/5/7
no switchport
no ip address
no cdp enable
channel-group 1 mode on
!
interface TenGigabitEthernet1/5/8
no switchport
no ip address
no cdp enable
channel-group 1 mode on
interface Port-channel2
no switchport
no ip address
no platform qos channel-consistency
switch virtual link 2
interface TenGigabitEthernet2/5/7
no switchport
no ip address
no cdp enable
channel-group 2 mode on
!
interface TenGigabitEthernet2/5/8
no switchport
no ip address
no cdp enable
channel-group 2 mode on
sh switch virtual dual sum
Pagp dual-active detection enabled: Yes
Fast-hello dual-active detection enabled: Yes
FEX dual-active detection enabled: Yes
No interfaces excluded from shutdown in recovery mode
In dual-active recovery mode: No
sh switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 1
Local switch number : 1
Local switch operational role: Virtual Switch Active
Peer switch number : 2
Peer switch operational role : Virtual Switch Standby
C6880X-SSV-D7WC4#sh switch virtual link
VSL Status : UP
VSL Uptime : 14 hours, 36 minutes
VSL SCP Ping : Pass
VSL ICC Ping : Pass
VSL Control Link : Te1/5/7
VSL Encryption : Configured Mode - Off, Operational Mode - Off
sh switch virtual role
RRP information for Instance 1
--------------------------------------------------------------------
Valid Flags Peer Preferred Reserved
Count Peer Peer
--------------------------------------------------------------------
TRUE V 1 1 1
Switch Switch Status Priority Role Local Remote
Number Oper(Conf) SID SID
--------------------------------------------------------------------
LOCAL 1 UP 200(200) ACTIVE 0 0
REMOTE 2 UP 100(100) STANDBY 8204 7706
Peer 0 represents the local switch
Flags : V - Valid
In dual-active recovery mode: No
02-17-2019 12:14 PM
Hello,
does a 'normal' failover work (redundancy force-switchover) ?
02-17-2019 11:40 PM
I'll try it during another downtime, thanks for suggesting!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide