06-19-2023 03:45 AM
I'm in the process of commissioning some new 9200L switches on our network. I've created a new VLAN/ subnet for them which is working and I have L3 connectivity. However, when connected to the existing site network- currently as a spur but will eventually form a ring connection once all devices installed, I cannot ping the IP allocated to the 9200L from either same subnet or different subnet. The I only get a reply from ping test doing it from the L3 switch or when directly connected to the new 9200L switch from a laptop on LAN.
I know the 9200L is able to respond to ping as per latter point above, but because of this I am unable to test connectivity OR more importantly gain SSH connection from elsewhere on network. I'm out of ideas and could use a fresh perspective- hopefully I'm missing something silly!!
Grateful for any suggesstions.
L3 device is a 9300 with direct connection via fiber to 9200L.
Solved! Go to Solution.
06-21-2023 04:12 AM - edited 06-21-2023 04:44 AM
Might or might not help but "ip default-gateway IP" and "ip route 0.0.0.0 0.0.0.0 IP" are not the same.
ip default-gateway is used when the switch is L2 only. (ip routing disabled)
ip route 0.0.0.0 ... is used mainly when the switch is L3 (ip routing enabled)
More info here: https://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/16448-default.html
Richard
06-19-2023 03:48 AM
Mgmt vlan must allow in trunk between 9200 and 9300
06-19-2023 06:11 AM
trunk between 9200 and 9300l already set to allow all vlans due to design of network in this are
06-19-2023 02:11 PM - edited 06-21-2023 09:15 AM
check my below post for solution
06-19-2023 02:34 PM
Sw 9200 have mgmt vlanx
Sw 9300 l3sw have vlanx svi
Points to check:-
The sw 9200 l2sw have defualt getaway toward vlanx svi in 9300 l3sw
The vlanx is allow in trunk along the path between sw9200 and sw9300
The vlanx svi is UP in sw9300 l3sw
That it
Thanks
MHM
06-19-2023 04:21 AM
Hi
Would be helpful if you could share the show running config but if you can ping from the L3 switch, which a believe must be the gateway, but can not ping remotelly, I wonder if you have default-gateway setup. I would try to add a default route pointing to L3 switch instead the command ip default-gateway.
06-19-2023 06:15 AM
It is setup the same way as other switches i have elsewhere and they can communicate fine. DG is setup on VLAN/ subnet also. I can ping other IPs located on the VLAN in question from my pc (differnet vlan/subnet) or L3 switch, but not the two that are currently assigned to the two 9200L switches being commissioned. It's behaving like the fact it's assigned to that switch is what's causing it to not reply.
06-19-2023 06:19 AM - edited 06-19-2023 06:19 AM
Can you share the show run from one of those 9200, just to make sure you are not missing something and someone here can see?
But, the way you put it, I start to think about a bug. If you have DG properly and you can ping from L3 sw, a bug could be an explanation..
06-19-2023 06:21 AM
I can arrange a copy of the show run later, not physically able to now.
They currently have the same ios version as they were shipped with. Do you know if the latest version is clear of any bugs? Problems with the firmware the switches are currently running is granted not something i had thought of...!
06-19-2023 06:44 AM
One thing I no is that no version is clear of bugs. But, if they have the same version then is less likely to be a bug
06-19-2023 05:01 AM
Hi,
You should enable "ip routing" as (I had the same issue on c9300 a week ago) these devices are switches by default and routing is not enabled. Tricky, as it accepts all L3 commands but just working.
Richard
06-19-2023 06:18 AM
Can you please elaborate on this- where would this be enabled and how? The 9300 is able to route traffic between all other VLANs already, it appears to be specifically routing to the two IPs currently assigned to the two 9200L that are exhibiting the problem. Hope this makes sense.
06-19-2023 06:28 AM
Hi,
There is a command "ip routing" in config mode which enable unicast routing.
Section "Configuration Guidelines for IP routing" :
By default, IP routing is disabled on the device, and you must enable it before routing can take place.
Richard
06-20-2023 04:46 AM
So, I have now enabled ip routing on the 9200L AND created a new port-channel for the connection between the 9200L and 9300 so that LACP will work on the 9200L. Needed to do this anyway, so this gave me a cause to.
Either way it's still not working.
I have checked the firmware and they are somewhat out of date so I need to install the latest recommended version (just downloaded from cisco)
06-20-2023 04:49 AM - edited 06-20-2023 05:36 AM
Sw 9200 have mgmt vlan x svi
Sw 9300 l3sw have vlan x svi
Points to check:-
The sw 9200 l2sw have defualt getaway toward vlan x svi in 9300 l3sw (9200 must l2sw)
The vlan x is allow in trunk along the path between sw9200 and sw9300 <<- this so important
The vlan x svi is UP in sw9300 l3sw
That it
Thanks
MHM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide