can't using ip routing in 3750x 24t -l

[chenyizhen]

Why can not I do with ‘’ip routing" and static route in 3750x 24t -l.

can you help me to solve this problem ，thans！！

[Leo Laohoo]

Post the output:  sh license

[chenyizhen]

[Leo Laohoo]

You can't enable IP Routing because you haven't accepted the EULA.

PS:  Please don't post screenshots.  Use cut-and-paste.

[muca]

Hi Leo,

I have the same issue. I accepted the EULA as suggested, using  the "license boot level ipservices". Switch restarted and then I was  able to  issue the "ip routing" command, however when I changed it back  to level lanbase then no ip routing command.

Any ideas?

See below the output of show license after "enabling" ip services.

DCSG-PENROSE-DC#show lic

DCSG-PENROSE-DC#show license

Index 1 Feature: ipservices

        Period left: 8  weeks 4  days

        License Type: Evaluation

        License State: Active, In Use

        License Priority: Low

        License Count: Non-Counted

Index 2 Feature: ipbase

        Period left: 0  minute  0  second

Index 3 Feature: lanbase

        Period left: Life time

        License Type: Permanent

        License State: Active, Not in Use

        License Priority: Medium

        License Count: Non-Counted

Regards,

Murilo

[Leo Laohoo]

"ip routing" is only available with IP Services feature set. This is why when you went back to LAN Base or IP Base, the command is disabled.

Sent from Cisco Technical Support Nintendo App

[muca]

Thanks Leo. I think you are right.

I guess something wrong with this document then.

High-Performance IP Routing

Cisco  Express Forwarding hardware routing architecture delivers extremely  high-performance IP routing in the Cisco Catalyst 3750-X and 3560-X  Series Switches.

• Static routing (16 routes) with LAN Base feature set.

But then also this on the same document

Cisco Catalyst 3750-X and 3560-X Series Software

In  addition to IP Base and IP Services feature sets, the Cisco Catalyst  3750-X and 3560-X Series come with a new LAN Base feature set. The three  feature sets available with all Cisco Catalyst 3750-X and 3560-X Series  Switches are:

• LAN Base: enterprise access Layer 2 switching features

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps6406/data_sheet_c78-584733.html

[Leo Laohoo]

And exactly what routing protocols are you planning to use?

[muca]

Just static routes but I think you were correct on your first statement, LAN base is only a layer2.

Don't think LAN base supports "16 static" routes.

In   addition to IP Base and IP Services feature sets, the Cisco Catalyst   3750-X and 3560-X Series come with a new LAN Base feature set. The  three  feature sets available with all Cisco Catalyst 3750-X and 3560-X  Series  Switches are:

• LAN Base: enterprise access Layer 2 switching features

[Jose Solano]

Hi,

According to the configuration guide:http://www.cisco.com/en/US/docs/switches/lan/catalyst3750x_3560x/software/release/12.2_58_se/configuration/guide/swiprout.html#wp1118518

Starting with Cisco IOS Release 12.2(58)SE, switches running the LAN base image support 16 user-configured static routes on SVIs. Static routing configuration is supported on the LAN base image only with the default SDM template and only on SVI interfaces. No routing protocols are supported.

Hope this helps..

[muca]

Awesome. Thanks for that....looks like an IOS upgrade.

Was running 12.2(55)SE8

[HAMZA NISAR]

muca what you have done with this issue i've the same issue

[Leo Laohoo]

Read this.

Please don't forget to rate our useful posts.