02-17-2019 06:37 PM - edited 03-08-2019 05:22 PM
Hi can one help whats wrong with the router
as i turn on my router it stays like this and cannot proceed to my login banner.
need Help
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco CISCO2911/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1550110G
3 Gigabit Ethernet interfaces
1 terminal line
3 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
255744K bytes of ATA System CompactFlash 0 (Read/Write)
no logging discriminator
% Incomplete command.
Logging of %SNMP-3-AUTHFAIL is disabled
logging queue-limit esm 0
^
% Invalid input detected at '^' marker.
ipc holdq threshold upper 0
^
% Invalid input detected at '^' marker.
ipc holdq threshold lower 0
^
% Invalid input detected at '^' marker.
cef table vrf tree IPv6 type RTREE
^
% Invalid input detected at '^' marker.
cef table output-chain build favor default
^
% Invalid input detected at '^' marker.
ipv6 nd ns-interval 0
^
% Invalid input detected at '^' marker.
ipv6 nd dad time 0
^
% Invalid input detected at '^' marker.
no ip cef accounting
% Incomplete command.
ip nbar port-map h323 tcp 1300 1718 1719 1720 11000 - 11999
^
% Invalid input detected at '^' marker.
ip nbar port-map custom-10 udp
% Incomplete command.
ip nbar port-map custom-10 tcp
% Incomplete command.
ip nbar port-map custom-09 udp
% Incomplete command.
ip nbar port-map custom-09 tcp
% Incomplete command.
ip nbar port-map custom-08 udp
% Incomplete command.
ip nbar port-map custom-08 tcp
% Incomplete command.
ip nbar port-map custom-07 udp
% Incomplete command.
ip nbar port-map custom-07 tcp
% Incomplete command.
ip nbar port-map custom-06 udp
% Incomplete command.
ip nbar port-map custom-06 tcp
% Incomplete command.
ip nbar port-map custom-05 udp
% Incomplete command.
ip nbar port-map custom-05 tcp
% Incomplete command.
ip nbar port-map custom-04 udp
% Incomplete command.
ip nbar port-map custom-04 tcp
% Incomplete command.
ip nbar port-map custom-03 udp
% Incomplete command.
ip nbar port-map custom-03 tcp
% Incomplete command.
ip nbar port-map custom-02 udp
% Incomplete command.
ip nbar port-map custom-02 tcp
% Incomplete command.
ip nbar port-map custom-01 udp
% Incomplete command.
ip nbar port-map custom-01 tcp
% Incomplete command.
no ip sctp authenticate init
^
% Invalid input detected at '^' marker.
no ip sctp authenticate init-ack
^
% Invalid input detected at '^' marker.
no ip sctp authenticate shutdown-complete
^
% Invalid input detected at '^' marker.
no ip sctp authenticate authentication
^
% Invalid input detected at '^' marker.
ip pgm host join 0
^
% Invalid input detected at '^' marker.
kerberos timeout 15
^
% Invalid input detected at '^' marker.
multilink virtual-template 0
^
% Invalid input detected at '^' marker.
WARNING!: secondary export device is same as primary
%Text Relay needs to be enabled before the options being configured
Cannot set maximum when backing up to network path
time-period 0
^
% Invalid input detected at '^' marker.
crypto ikev2 nat keepalive 0
^
% Invalid input detected at '^' marker.
crypto ikev2 dpd 0 0 periodic
^
% Invalid input detected at '^' marker.
crypto ikev2 limit max-sa 0
^
% Invalid input detected at '^' marker.
ip tcp mss 0
^
% Invalid input detected at '^' marker.
ip tftp min-timeout 3000
^
% Invalid input detected at '^' marker.
buffers header min-free 128
^
% Invalid input detected at '^' marker.
buffers header initial 0
^
% Invalid input detected at '^' marker.
buffers fastswitching min-free 256
^
% Invalid input detected at '^' marker.
buffers fastswitching initial 0
^
% Invalid input detected at '^' marker.
%GigabitEthernet0/0 is a static pool and cannot be tuned
%GigabitEthernet0/0 is a static pool and cannot be tuned
%GigabitEthernet0/0 is a static pool and cannot be tuned
%GigabitEthernet0/0 is a static pool and cannot be tuned
%GigabitEthernet0/1 is a static pool and cannot be tuned
%GigabitEthernet0/1 is a static pool and cannot be tuned
%GigabitEthernet0/1 is a static pool and cannot be tuned
%GigabitEthernet0/1 is a static pool and cannot be tuned
%GigabitEthernet0/2 is a static pool and cannot be tuned
%GigabitEthernet0/2 is a static pool and cannot be tuned
%GigabitEthernet0/2 is a static pool and cannot be tuned
%GigabitEthernet0/2 is a static pool and cannot be tuned
ipv6 nd ns-interval 0
^
% Invalid input detected at '^' marker.
02-17-2019 06:56 PM
Hi,
Try this link to see if you can recover the image or load a new one.
HTH
02-17-2019 07:21 PM
hi
I guess this works when i could atleast see my login or cmd prompt
i get these mesges when i even turn my router on and after a sec it shows these mesges in putty and then thats it.. cannot move any further..
any thing else can you help
02-18-2019 04:06 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide