Hi everyone, i'm having a problem with a network in my simulator, i have network with a router making 2 subnets, every subnet have a switch. The problem is i cannot ping from a pc to the router, doesn't reach the router, only the switch.
The simulator says that there's "No communication protocol is presente for router 2600.A protocol needs to be present that allows communication to take place. You need either default/static routes established, RIP running, or IGRP running."
The router active configuration (my subnets are in the FastEthernet ports)(Cisco 2600) :
Router(config)#show running-config
^
% Invalid input detected at '^' marker.
Router(config)#exit
Router#show running-config
Building configuration...
Current configuration : 625 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
!
!
ip subnet-zero
!
!
!
!
!
interface FastEthernet0/0
ip address 10.87.200.1 255.255.255.0
no ip directed-broadcast
!
interface Serial0/0
ip address 10.82.15.2 255.255.255.0
no ip directed-broadcast
!
interface FastEthernet0/1
ip address 10.87.201.1 255.255.255.0
no ip directed-broadcast
!
interface Serial0/1
ip address 10.82.73.2 255.255.255.0
no ip directed-broadcast
!
router rip
version 2
network 10.0.0.0
!
!
ip classless
no ip http server
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
end
Router#show cdp neighbor
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater
Device ID Local Intrfce Holdtme Capability Platform Port ID
Router Ser 0/1 170 R 2621 Ser 0/1
Router Ser 0/0 170 R 2621 Ser 0/0
switch Fas 0/12 170 SI 2950 Fas 0/1
switch Fas 0/12 170 SI 2950 Fas 0/0
Router Con0 is now available
Press RETURN to get started!
Router>enable
Router#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 14 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 2, receive version 2
Interface Send Recv Triggered RIP Key-chain
Serial0/1 1 1 2
Serial0/0 1 1 2
FastEthernet0/1 1 1 2
FastEthernet0/0 1 1 2
Automatic network summarization is in effect
Maximum path: 4
Routing for networks:
10.0.0.0
Routing information sources:
Gateway Distance Last Update
Distance: <default is 120>
Router#show ip route rip
10.0.0.0/24 is subnetted, 4 subnets
Router#
This is the information of switch (Catalyst 2950):
switch#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname switch
!
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface Vlan1
ip address 10.87.200.254 255.255.255.0
no ip route-cache
!
ip default-gateway 10.87.200.1
ip http server
!
!
line con 0
line vty 0 15
login
!
end
If something else is needed, please let me know. Thanks and regards.
