03-29-2011 05:07 PM - edited 03-06-2019 04:20 PM
Gents
Our customer need to setup a few link aggregations on a Cat4000 switch for increasing their blade servers' throughput and the IOS which currently running is cat4000-is-mz.121-20.E.bin. But I don't see the switch's IOS supports LACP. Since there is no way to enter "channel-protocol / channel-group # mode active / passive" to the switch.
I wonder if anyone know the right IOS ver which can support LACP on that switch or if there is a way to work around without network outage.
Appreciate for your thoughts!
Adit Tao
03-29-2011 06:11 PM
Hi,
What type of Sup module does your 4000 have?
Reza
03-29-2011 10:50 PM
Thanks Reza, following are the show run and show module output and no sup info in this switch.
show run
IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-IS-M), Version 12.1(20)E, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 24-Oct-03 07:26
Image text-base: 0x00000000, data-base: 0x00D589FC
ROM: 12.1(12r)EW
Dagobah Revision 63, Swamp Revision 28
GFLAUULTSW01 uptime is 1 year, 22 weeks, 5 days, 7 hours, 31 minutes
System returned to ROM by power-on
System restarted at 09:08:03 DEST Thu Oct 22 2009
System image file is "bootflash:"
cisco WS-C4506 (XPC8245) processor (revision 7) with 524288K bytes of memory.
Processor board ID FOX071004SW
Last reset from PowerUp
4294967294 Ethernet/IEEE 802.3 interface(s)
146 Gigabit Ethernet/IEEE 802.3 interface(s)
403K bytes of non-volatile configuration memory.
show module
Mod Ports Card Type Model Serial No.
----+-----+--------------------------------------+-----------------+-----------
1 2 1000BaseX (GBIC) Supervisor(active) WS-X4515 JAE07420DHV
3 48 10/100/1000BaseTX (RJ45) WS-X4448-GB-RJ45 JAB0825062R
4 48 10/100/1000BaseTX (RJ45) WS-X4448-GB-RJ45 JAE0919BVHD
5 48 10/100/1000BaseTX (RJ45) WS-X4448-GB-RJ45 JAB072004TS
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 000c.85f5.a140 to 000c.85f5.a141 3.0 12.1(12r)EW 12.1(20)E, EARLY Ok
3 0011.2101.5b40 to 0011.2101.5b6f 1.1 Ok
4 0013.c4a5.82d0 to 0013.c4a5.82ff 1.2 Ok
5 000c.cef5.1420 to 000c.cef5.144f 1.1 Ok
03-29-2011 11:41 PM
Hi Tao,
Please goes through Cisco Feature Navigator to locate the IOS which supports Link Aggregation (Looks like it will not support):
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
Regards,
Akhil
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide