11-30-2012 01:44 AM - edited 03-07-2019 10:20 AM
Hi,
we have observed increase of CPU utilization of 50% after upgrade from 15.0(1)SE3 to 15.0(2).
The SDM template is "desktop default" template.
The increase of CPU utilization in Switches with LAN Base after upgrade is about 10%.
Has somebody an idea to find the cause for the 50% increase ?
This is command is the output of 15.0(2). The calculated sum for 5min process-utilization is 21% plus
1% interrupt is 22 %. Where is the rest ?
switch#sh proc cpu sorted 5min | exc 0.00
CPU utilization for five seconds: 30%/1%; one minute: 29%; five minutes: 28%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
169 135084171 33273787 4059 9.92% 8.94% 8.73% 0 Hulc LED Process
83 80075989 13546109 5911 5.60% 5.39% 5.38% 0 RedEarth Tx Mana
82 35961521 22044350 1631 2.40% 2.58% 2.57% 0 RedEarth I2C dri
4 23049116 1025093 22485 2.87% 1.16% 1.52% 0 Check heaps
126 12684154 1334361 9505 0.79% 0.91% 0.89% 0 hpm counter proc
233 14289030 36476685 391 0.95% 0.90% 0.88% 0 Spanning Tree
181 4784768 265620 18013 0.31% 0.35% 0.32% 0 HQM Stack Proces
401 3112704 4956783 627 0.15% 0.21% 0.21% 0 SNMP ENGINE
54 1528521 1334812 1145 0.31% 0.13% 0.11% 0 Per-Second Jobs
182 1521435 531267 2863 0.15% 0.11% 0.10% 0 HRPC qos request
302 1463582 2928584 499 0.15% 0.10% 0.10% 0 Marvell wk-a Pow
249 1373699 1322338 1038 0.15% 0.08% 0.10% 0 PI MATM Aging Pr
107 1522052 37139967 40 0.31% 0.06% 0.09% 0 HLFM address ret
400 886100 4956777 178 0.15% 0.04% 0.04% 0 PDU DISPATCHER
regards,
Herbert
12-13-2012 05:41 PM
Switch#show proc cpu sort | ex 0.00%
CPU utilization for five seconds: 28%/0%; one minute: 30%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
159 26560911 3171461 8374 15.65% 15.50% 15.48% 0 Hulc LED Process
75 6901005 1087280 6347 4.15% 3.99% 4.02% 0 RedEarth Tx Mana
74 2767996 1803547 1534 1.59% 1.68% 1.67% 0 RedEarth I2C dri
119 2624042 155931 16828 1.59% 1.55% 1.58% 0 hpm counter proc
4 1943065 86466 22472 0.47% 0.99% 1.09% 0 Check heaps
170 549842 31877 17248 0.31% 0.32% 0.31% 0 HQM Stack Proces
Maybe I configured load-interval 30 under every L3 interface ?
12-13-2012 01:44 PM
I agree, with Aru. Your CPU value is "normal". It ain't high but it's tolerable.
12-13-2012 05:51 PM
Hi Leo,
Thank you!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide