09-26-2018 03:23 AM - edited 03-08-2019 04:15 PM
We have a CAT9K with IOS-XE Version 16.8.1a
When I try to execute the upgrade commands for ISSU I get the below error:
FAILED: ACTIVATE operation is not allowed in SWITCHED_OVER state
Somehow I cannot seem to go around this issue (marked below in green) I googled my way around but I didnt find an answerd, maybe somebody can shed some light on this case. How to get it out active switched-over state ?
Its the only 9500 we have, the catalyst 4500 in VSS show different information under the the show issu state detail so I have also no compare information :).
FYI:
Before I issued the "activate issu" command (with my console port plugged into the Active switch)
I issued the install add file tftp://172.16.16.2/ cat9k_iosxe.16.09.01.SPA.bin
------
Here some information about the state of the current stackwise virtual:
Switch#install activate issu
install_activate: START Wed Sep 26 09:19:14 UTC 2018
install_activate: Activating ISSU
*Sep 26 09:19:15.570: %INSTALL-5-INSTALL_START_INFO: Switch 1 R0/0: install_engine: Started install activate ISSU
NOTE: Going to start Activate ISSU install process
STAGE 0: Initial System Level Sanity Check before starting ISSU
===================================================
--- Verifying install_issu supported ---
--- Verifying standby is in Standby Hot state ---
--- Verifying booted from the valid media ---
--- Verifying AutoBoot mode is enabled ---
Finished Initial System Level Sanity Check
FAILED: ACTIVATE operation is not allowed in SWITCHED_OVER state
ERROR: install_activate exit(2 ) Wed Sep 26 09:19:18 UTC 2018
-------------------------
!
Switch#show switch
Switch/Stack Mac Address : 00aa.6ef3.8c80 - Local Mac Address
Mac persistency wait time: Indefinite
H/W Current
Switch# Role Mac Address Priority Version State
-------------------------------------------------------------------------------------
*1 Active 00aa.6ef3.8c80 1 V01 Ready
2 Standby 00b6.7039.df80 1 V01 Ready
Switch#show issu state detail
--- Starting local lock acquisition on switch 1 ---
Finished local lock acquisition on switch 1
Operation type: Step-by-step ISSU
Step-by-step ISSU
Install type : Image installation using ISSU
Current state : Active switched-over state
Last operation: Abort
Completed operations:
Operation Start time
-------------------------------------------------------
Activate location standby Chassis 2 2018-08-21:11:57:56
Activate location standby Chassis 2 2018-09-10:12:57:19
Switchover 2018-09-11:09:37:17
Switchover 2018-09-11:10:47:09
Abort 2018-09-19:09:33:03
State transition: Added -> Added -> Standby activated -> Active switched-over -> Active switched-over
Auto abort timer: inactive
Running image: flash:packages.conf
Operating mode: sso, terminal state reached
!
Switch#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 20 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 1
Current Software state = ACTIVE
Uptime in current state = 20 minutes
Image Version = Cisco IOS Software [Fuji], Catalyst L3 Switch SoftwarCAT9K_IOSXE), Version 16.8.1a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Tue 03-Apr-18 18:49 by mcpre
BOOT = flash:packages.conf
CONFIG_FILE =
Configuration register = 0x102
Peer Processor Information :
----------------------------
Standby Location = slot 2
Current Software state = STANDBY HOT
Uptime in current state = 15 minutes
Image Version = Cisco IOS Software [Fuji], Catalyst L3 Switch SoftwarCAT9K_IOSXE), Version 16.8.1a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Tue 03-Apr-18 18:49 by mcpre
BOOT = flash:packages.conf
CONFIG_FILE =
Configuration register = 0x102
09-26-2018 03:34 AM
09-26-2018 03:40 AM
05-16-2019 11:48 AM
Andy,
Did you ever find a way to us ISSU to do a graceful update.
Thanks,
Tom
01-20-2021 08:04 PM
Hi all, the command that did the trick for me was:
install activate location standby
This brought me out of the switched-over state so that I could then "install commit" without getting the error:
FAILED: COMMIT operation is not allowed in SWITCHED_OVER state
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide