cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
791
Views
3
Helpful
2
Replies

Cisco 2610 terminal server

wayne_fan
Beginner
Beginner

I got a terminal server with 2 octal cables attached to it. each octal cable has 8 RJ45 plugs. I installed a patch panel today and plug them into the back of the patch panel. I'll use the front panel as Out of Band ports.

However I can't access other device from my terminal server. I used rollover cable between the patch panel and my device. I was thinking maybe the octal cable is already rolled over. here are my partial output.

line 33 48

session-timeout 5

exec-timeout 5 0

flush-at-activation

no exec

transport input all

transport output none

escape-character BREAK

telnet ip-on-break

stopbits 1

flowcontrol hardware

AS05#sh line

Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

0 CTY - - - - - 0 0 0/0 -

* 33 TTY 9600/9600 - - - - - 1 0 0/0 -

* 34 TTY 9600/9600 - - - - - 1 0 0/0 -

35 TTY 9600/9600 - - - - - 0 0 0/0 -

36 TTY 9600/9600 - - - - - 0 0 0/0 -

37 TTY 9600/9600 - - - - - 0 0 0/0 -

38 TTY 9600/9600 - - - - - 0 0 0/0 -

39 TTY 9600/9600 - - - - - 0 0 0/0 -

40 TTY 9600/9600 - - - - - 0 0 0/0 -

41 TTY 9600/9600 - - - - - 0 0 0/0 -

42 TTY 9600/9600 - - - - - 0 0 0/0 -

43 TTY 9600/9600 - - - - - 0 0 0/0 -

44 TTY 9600/9600 - - - - - 0 0 0/0 -

45 TTY 9600/9600 - - - - - 0 0 0/0 -

46 TTY 9600/9600 - - - - - 0 0 0/0 -

47 TTY 9600/9600 - - - - - 0 0 0/0 -

* 48 TTY 9600/9600 - - - - - 1 0 0/0 -

65 AUX 9600/9600 - - - - - 2 0 0/0 -

* 66 VTY - - - - - 7 0 0/0 -

67 VTY - - - - - 4 0 0/0 -

68 VTY - - - - - 0 0 0/0 -

69 VTY - - - - - 0 0 0/0 -

70 VTY - - - - - 0 0 0/0 -

Line(s) not in async mode -or- with no hardware support:

1-32, 49-64

1 Accepted Solution

Accepted Solutions

mohammedmahmoud
Advisor
Advisor

Hi,

The octal cable is already rolled, you need a straight cable from the patch panel to your device, and your posted configuration seems fine.

BR,

Mohammed Mahmoud.

View solution in original post

2 Replies 2

dmisell
Beginner
Beginner

Wayne,

The following used to be recommended somewhere in CCO and is current:

http://www.conserver.com/consoles/msock.html

http://www.conserver.com/consoles/

For something like a Cat 5500 you would normally use an OLD Style cisco headshell and straight through cable from the laptop. A router/asa would use a rollover.

Conversely you might use an octal into a back to back panel and patch a rollover into a 5500 switch and straight through into a router or modern ASA 5500.

The zeros are a bit of a giveaway and indicate negative comms, so check your patching, and look for the lights on the ASYN 32/16 or terminal server.

Hope this helps

kind regards

dave

david.misell@iee.org

mohammedmahmoud
Advisor
Advisor

Hi,

The octal cable is already rolled, you need a straight cable from the patch panel to your device, and your posted configuration seems fine.

BR,

Mohammed Mahmoud.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers