02-25-2011 01:35 AM - edited 03-06-2019 03:45 PM
Hi all,
I have a ws-cisco 3560x-48p (running Version 12.2(53)SE2, RELEASE SOFTWARE (fc3) trying to use poe+ to power a cisco AIR-AP1252AG-N-K9
(running Version 12.4(21a)JY, RELEASE SOFTWARE (fc1))
The wap is showing a combination of green, blue and red lights indicating it is running in low power mode.
I ssh into the wap and running show cont dot11Radio 1 displays:
"Radio is running in lower power mode due to inline power (15.4 W)
Maximum transmit power will be affected
Allowed data rates and antennas will be affected"
I have tried power static max 30000 on the cisco switch however it is still saying its running on inline power 15.4.
Is it possible to run this wap from the cisco switch in poe+ or will I have to use the power injector (which works fine)
Any ideas? We are using autonomous ap's with no WLC. Cdp has been turned off the waps (It has been disabled and I cant enable it as I dont have the enable password) Thanks.
show power inline displays:
Interface Admin Oper Power Device Class Max
(Watts)
Gi0/3 static on 30.0 Ieee PD 3 30.0
02-25-2011 01:45 AM
I've got 1252 connected to 3560E. I've enabled PoE up to 20.0w and they are working fine.
I think you need to upgrade the IOS to fix this.
03-08-2011 03:55 AM
Hi all,
Can anyone please confirm with a more detailed answer. Will upgrading the firmware to the latest fix this issue? I thought I was running the latest.
Thanks
03-08-2011 01:36 PM
Gi0/20 auto on 20.0 AIR-LAP1252AG-N-K9 3 20.0
Gi0/21 auto on 20.0 AIR-LAP1252AG-N-K9 3 20.0
Gi0/22 auto on 20.0 AIR-LAP1252AG-N-K9 3 20.0
Gi0/23 auto on 20.0 AIR-LAP1252AG-N-K9 3 20.0
Gi0/24 auto on 20.0 AIR-LAP1252AG-N-K9 3 20.0
power inline port maximum 20000
That's my setup.Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE
03-08-2011 03:54 PM
I have tried the same command, same problem.
Can you tell me the exact reason, e.g is there a difference between IOS versions? I read the release notes but not much mentioned regarding poe issues.
You are running Version 12.2(55)SE and I'm using 12.2(53)SE2
I tried your command, appears to be missing?
libcorecisco1(config-if)#power inline port maximum ?
% Unrecognized command
libcorecisco1(config-if)#power inline port maximum 20000
^
% Invalid input detected at '^' marker.
What is the problem?
libcorecisco1(config-if)#power inline ?
auto Automatically detect and power inline devices
consumption Configure the inline device consumption
never Never apply inline power
police Police the power drawn on the port
port Configure Port Power Level
static High priority inline power interface
libcorecisco1(config-if)#power inline port ?
priority set power priority of the port
03-08-2011 04:56 PM
Ok then. Try the command "power inline auto max
03-09-2011 04:04 AM
Did this work?
03-15-2011 10:15 PM
After your command:
Gi0/3 auto on 15.4 Ieee PD 3 20.0
It is still not providing the full 20 watt for this 1252 wap.
CDP is off on the wap, this could be the reason why its not detecting what kind of wap this is and what power to provide?
Even with the static max command, I would have thought it would provide 20w, however in my case its running in low power mode.
Any more ideas?
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide