06-02-2015 11:42 PM - edited 03-08-2019 12:19 AM
Dears,
I have core 6506 with POE Ethernet module. I connected cisco Access points and telephone devices and it was supply them power normally.
Now the Ethernet module stop to supply the POE for these devices and I got the below messages:-
The device connected to 1/38 is powered up but its link is not up in 5 seconds. Therefore, power is withdrawn from the port.
The device connected to 1/38 is powered up but its link is not up in 5 seconds. Therefore, power is withdrawn from the port.
pd_scp_power_req_resp_ver2: rx scp err code = 1
Your ideas is highly appreciated,
Regards,
06-03-2015 01:05 AM
Post the complete output to the following commands:
1. sh power inline G1/38; and
2. sh interface G1/38
06-03-2015 02:52 AM
nterface Admin Oper Power(Watts) Device Class
From PS To Device
--------- ------ ---------- ---------- ---------- ------------------- ------
Gi1/38 auto off 0 0 n/a n/a
Interface AdminPowerMax Police ActualConsumption
(Watts)
---------- ----------------- ---------- -------------------
Gi1/38 15.4 off n/a
Core#
GigabitEthernet1/38 is down, line protocol is down (notconnect)
Hardware is C6k 1000Mb 802.3, address is f0f7.558a.e800 (bia f0f7.558a.e800)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is desired
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
06-03-2015 04:42 AM
The output to the command "sh power inline G1/38" is not complete. :P
06-03-2015 01:23 AM
Is the issue with just one port or all of the ports on that module?
06-03-2015 01:28 AM
I checked 5 ports only and have the same issue but I didn't check all module ports.
The issue is only with POE but when I connect PC it's working normally.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide