ok, Is there any specific configuration, because when I configured it I got the outside dial tone once click on 9 as the cucm doesn't wait for the next digit (1). Please advise, ... View more

Thank Jaime, My point that I need to use the 91 as an outside dial tone instead of 9, is this possible? ... View more

nterface Admin  Oper            Power(Watts)     Device              Class                             From PS    To Device --------- ------ ---------- ---------- ---------- ------------------- ------ Gi1/38    auto   off        0          0          n/a                 n/a Interface  AdminPowerMax       Police    ActualConsumption              (Watts) ---------- -----------------  ----------  ------------------- Gi1/38                15.4       off            n/a Core# GigabitEthernet1/38 is down, line protocol is down (notconnect)   Hardware is C6k 1000Mb 802.3, address is f0f7.558a.e800 (bia f0f7.558a.e800)   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation ARPA, loopback not set   Keepalive set (10 sec)   Auto-duplex, Auto-speed, media type is 10/100/1000BaseT   input flow-control is off, output flow-control is desired   Clock mode is auto   ARP type: ARPA, ARP Timeout 04:00:00   Last input never, output never, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/40 (size/max)   5 minute input rate 0 bits/sec, 0 packets/sec   5 minute output rate 0 bits/sec, 0 packets/sec   L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes   L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes   L3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes      0 packets input, 0 bytes, 0 no buffer      Received 0 broadcasts (0 IP multicasts) ARP type: ARPA, ARP Timeout 04:00:00   Last input never, output never, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/40 (size/max)   5 minute input rate 0 bits/sec, 0 packets/sec   5 minute output rate 0 bits/sec, 0 packets/sec   L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes   L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes   L3 out Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes      0 packets input, 0 bytes, 0 no buffer      Received 0 broadcasts (0 IP multicasts)      0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored      0 watchdog, 0 multicast, 0 pause input      0 input packets with dribble condition detected      0 packets output, 0 bytes, 0 underruns      0 output errors, 0 collisions, 2 interface resets      0 babbles, 0 late collision, 0 deferred      0 lost carrier, 0 no carrier, 0 PAUSE output      0 output buffer failures, 0 output buffers swapped out ... View more

I checked 5 ports only and have the same issue but I didn't check all module ports. The issue is only with POE but when I connect PC it's working normally. ... View more

Hi, The issue that I can't find the device itself in the CUCM. By the way my device is a third party so when I'm trying to add it I got the mentioned message.   ... View more

I have Cisco 5508 WLCs with HA (SSO) configuration. So in ISE under NW devices I should put one WLC IP?  ... View more

Hi Neno, the AAA are matches. Regarding the NADs (2x WLC) are listed under the ISE, and I think this is my issue. When I configured the SSO on the WLCs now I can ping only one ip for the both WLCs. So should I configured two NADs under the ISE with same IP?   ... View more