10-19-2011 07:56 AM - edited 03-07-2019 02:55 AM
we have cisco 6509-E with IOS 12.2(18)SXF8 & trying to Introduce this as Service Layer.
I wanted to upgrade the IOS code to 12.2(33)SXI6 OR SXI7 . I do not see any upgrade guide that points to me what are the caveats associated with this.
I found following documents:
I can see that I have minimum DRAM 512 for 12;2(33)SXI7 . we may need to order another flash card ( only 128M right now).
1 When I tried to dowload the New IOS Sotware I saw more options( IOS Field Programmle Devices) , IOS Boot images etc..
Is there any certain sequence this need to happen or some options are because of legacy reason.
2 When I tried to download the software ios I have the two option. I am not sure what this Main diffrence between following IOS :
ADVANCED ENTERPRISE SERVICES SSH s72033-adventerprisek9_wan-mz.122-33.SXI7.bin
ADVANCED ENT SERVICES SSH (MODULAR) s72033-adventerprisek9_wan-vz.122-33.SXI7.bin
3 According to
when I tried to use boot system command I do not get the option for disk0: or is this normal ?
test(config)#boot system ?
WORD TFTP filename or URL
flash Boot from flash memory
ftp Boot from a server via ftp
mop Boot from a Decnet MOP server
rcp Boot from a server via rcp
tftp Boot from a tftp server
Sincerely,
Viral
Solved! Go to Solution.
10-19-2011 08:21 AM
Viral
If you do a dir
you will see its called sup-bootdisk
6500-PE1#dir
Directory of sup-bootdisk:/
1 -rw- 75345892 May 9 2007 13:44:10 +00:00 s72033-ipservicesk9_wan-mz.122-18.SXE6b.bin
2 -rw- 126531876 Jun 20 2011 10:47:24 +00:00 s72033-ipservices_wan-mz.122-33.SXJ.bin
3 -rw- 33554432 Jun 21 2011 02:35:24 +00:00 sea_log.dat
4 -rw- 33554432 Jun 21 2011 02:36:02 +00:00 sea_console.dat
to actually do the boot system
boot system flash sup-bootdisk:s72033-ipservices_wan-mz.122-33.SXJ.bin
do a #sh bootvar to check
p.s i did a similar upgrade from Version 12.2(18)SXE6b
10-19-2011 08:21 AM
Viral
If you do a dir
you will see its called sup-bootdisk
6500-PE1#dir
Directory of sup-bootdisk:/
1 -rw- 75345892 May 9 2007 13:44:10 +00:00 s72033-ipservicesk9_wan-mz.122-18.SXE6b.bin
2 -rw- 126531876 Jun 20 2011 10:47:24 +00:00 s72033-ipservices_wan-mz.122-33.SXJ.bin
3 -rw- 33554432 Jun 21 2011 02:35:24 +00:00 sea_log.dat
4 -rw- 33554432 Jun 21 2011 02:36:02 +00:00 sea_console.dat
to actually do the boot system
boot system flash sup-bootdisk:s72033-ipservices_wan-mz.122-33.SXJ.bin
do a #sh bootvar to check
p.s i did a similar upgrade from Version 12.2(18)SXE6b
10-20-2011 08:38 AM
Thank you Rob, that did the trick.
my curiosity about modular image ended ended up with some nice information & I am lucky that I am not in the production yet.
I am using single binary image rather than installed file ( which basically creates file system & load appropriate code when needed ). Now, I am curious to move to installed file image but command install file does not work as described in the follwoing link. I hope somebody have answer for it.
http://www.xpresslearn.com/cisco/switching/upgrade-to-a-modular-ios-image
host#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISE_WAN-VM), Version 12.2(33)SXI7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 18-Jul-11 07:28 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
host uptime is 1 hour, 19 minutes
Uptime for this control processor is 1 hour, 17 minutes
Time since Dist2 switched to active is 1 hour, 17 minutes
System returned to ROM by reload at 09:38:14 EDT Thu Oct 20 2011 (SP by reload)
System image file is "sup-bootdisk:s72033-adventerprise_wan-vz.122-33.SXI7.bin"
Last reload reason: reload
cisco WS-C6509-E (R7000) processor (revision 1.4) with 516096K/8192K bytes of memory.
Processor board ID SMG1316NHGX
SR71000 CPU at 600Mhz, Implementation 1284, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
35 Virtual Ethernet interfaces
2 Gigabit Ethernet interfaces
21 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
host#show inst
host#show install ?
% Unrecognized command
host#ins?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide