Good morning,
I've managed the change the password on the switch and login to to the switch under privilege mode, and erase using the write erase, on rebooting I can see an IP address 25.180.66.205 is this a default on the switch or do I need to still remove the IP, or have I done something wrong
>> MDS-Bootloader-01.00.19 (Feb 1 2010 - 15:13:26), Build: 01.00.19
PowerPC
CPU: 8541, Version: 1.1, (SVR:0x807a0011)
Core: E500, Version: 2.0, (PVR:0x80200020)
Clocks: CPU: 999 MHz, CCB: 333 MHz,
DDR: 166 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
INFO: Booting off primary flash.
I2C: ready
DRAM: DDR: ddrioovcr 0x00000000
Total SDRAM memory is 512 MB
20000000
INFO: SDRAM tests PASSED.
DRAM: ECC initialization in progress...Done.
done.
INFO: Board rev = 3 type = 4 index 9032
L2 cache 256KB: enabled
IDE: Bus 0: OK
Device 0: Model: TOSHIBA THNCF256MDG Firm: 3.00 Ser#: TSBC256M06913T85170
Type: Hard Disk
Capacity: 244.5 MB = 0.2 GB (500736 x 512)
Booting bootflash:/m9100-s2ek9-kickstart-mz.5.2.2d.bin ...
..................
Automatic boot of image at addr 0x00000000 ...
Starting kernel...
Entered kgdb_console_init:1975
INIT: version 2.85 booting
Checking all filesystems....r. done.
Setting kernel variables done.
Setting the System Clock using the Hardware Clock as reference...System Clock set. Local time: Thu Dec 2 16:19:34 UTC 2021
Loading system software
Uncompressing system image: bootflash:/m9100-s2ek9-mz.5.2.2d.bin
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
INIT: Entering runlevel: 3
Starting NFS servers: nfsd mountd.
2021 Dec 2 16:20:07 Dec 2 16:20:07 %KERN-2-SYSTEM_MSG: Starting kernel... - kernel
2021 Dec 2 16:20:07 Dec 2 16:20:07 %KERN-1-SYSTEM_MSG: Entered kgdb_console_init:1975 - kernel
---- System Admin Account Setup ----
Do you want to enforce secure password standard (yes/no) [y]:
Enter the password for "admin":
Confirm the password for "admin": 2021 Dec 2 16:20:43 switch %PLATFORM-2-PS_OK: Power supply 1 ok (Serial number PAC150230E7)
2021 Dec 2 16:20:43 switch %PLATFORM-2-PS_FANOK: Fan in Power supply 1 ok
2021 Dec 2 16:20:43 switch %PLATFORM-2-PS_FAIL: Power supply 2 failed or shut down (Serial number PAC1112301M)
2021 Dec 2 16:20:43 switch %PLATFORM-2-FAN_OK: Fan module ok
2021 Dec 2 16:20:43 switch %PLATFORM-2-FAN_OK: Fan module ok
2021 Dec 2 16:20:43 switch %PLATFORM-2-FAN_OK: Fan module ok
---- Basic System Configuration Dialog ----
This setup utility will guide you through the basic configuration of
the system. Setup configures only enough connectivity for management
of the system.
Please register Cisco MDS 9000 Family devices promptly with your
supplier. Failure to register may affect response times for initial
service calls. MDS devices must be registered to receive entitled
support services.
Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.
Would you like to enter the basic configuration dialog (yes/no):
Would you like to enter the basic configuration dialog (yes/no):
Would you like to enter the basic configuration dialog (yes/no):
Would you like to enter the basic configuration dialog (yes/no):
Would you like to enter the basic configuration dialog (yes/no): n
User Access Verification
25.180.66.205 login: admin
Password:
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2012, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
switch#
switch#
Thanks
Paul
