cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

379
Views
0
Helpful
3
Replies
Highlighted
Beginner

Configuring NAT in multiples public server

Hi everyone,

I need to configure 5 public servers in my LAN. The IP Private addres are: 192.168.3.2, 192.168.3.3, 192.168.3.4 and 192.168.3.5. My ISP give me 5 public IP´s 190.93.50.106-110.

The interface configuration on cisco 2901 are:

Inside: 192.168.3.1

outside: 190.93.50.105

I can´t understand the method of configuration in cisco product for my case. Is little hard to understand Inside local, Inside global, Outside Global Outside local.

Note: In this router I only have public servers and dont need overload a Ip address for internal traffic

Thanks for your help

Everyone's tags (6)
1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
VIP Mentor

Re: Configuring NAT in multiples public server

Hello Daniel

Inside Local = Addresses assigned to devices inside your network

Inside Global = Addresses to which your inside devices are known to the outside ( outside you network)

Outside Local = Addresses assigned to devices outside your network - not known by devices inside your network

Outside Global = Addresses by which outside devices are known to the inside

IG addresses are mapped to IL addresses, and OL addresses are mapped OG addresses

                                                                                                    

HostA - (INSIDE)                                                                Host B (OUTSIDE)

192.168.3.2 (IL)   190.93.50.106 (IG)         ---->           200.200.200.3 (OL)   172.16.2.3 (OG)

192.168.3.2 (IL)    190.93.50.106 IG)       < ----            200.200.200.3 (OL)   172.16.2.3 OG)

ip nat inside source static

  A.B.C.D  Inside local IP address

  esp      IPSec-ESP (Tunnel mode) support

  network  Subnet translation

  tcp      Transmission Control Protocol

  udp      User Datagram Protocol

Basic one to one mapping  - specific host - to host

ip nat inside source static (inside local) (inside global)

ip nat inside source static 192.168.3.2 190.93.50.106

ip nat inside source static 192.168.3.3 190.93.50.107

ip nat inside source static 192.168.3.4 190.93.50.108

ip nat inside source static 192.168.3.5 190.93.50.109

to a specific port

ip nat inside source static tcp 192.168.3.2 80 190.93.50.106 80

ip nat inside source static tcp 192.168.3.3 80 190.93.50.107 80

ip nat inside source static tcp 192.168.3.4 80 190.93.50.108 80

ip nat inside source static tcp 192.168.3.5 80 190.93.50.109 80

res

Paul

Please don't forget to rate any posts that have been helpful.

Thanks.



kind regards
Paul

Please rate and mark posts accordingly if you have found any of the information provided useful.
It will hopefully assist others with similar issues in the future

View solution in original post

3 REPLIES 3
Highlighted
VIP Mentor

Re: Configuring NAT in multiples public server

Hello Daniel

Inside Local = Addresses assigned to devices inside your network

Inside Global = Addresses to which your inside devices are known to the outside ( outside you network)

Outside Local = Addresses assigned to devices outside your network - not known by devices inside your network

Outside Global = Addresses by which outside devices are known to the inside

IG addresses are mapped to IL addresses, and OL addresses are mapped OG addresses

                                                                                                    

HostA - (INSIDE)                                                                Host B (OUTSIDE)

192.168.3.2 (IL)   190.93.50.106 (IG)         ---->           200.200.200.3 (OL)   172.16.2.3 (OG)

192.168.3.2 (IL)    190.93.50.106 IG)       < ----            200.200.200.3 (OL)   172.16.2.3 OG)

ip nat inside source static

  A.B.C.D  Inside local IP address

  esp      IPSec-ESP (Tunnel mode) support

  network  Subnet translation

  tcp      Transmission Control Protocol

  udp      User Datagram Protocol

Basic one to one mapping  - specific host - to host

ip nat inside source static (inside local) (inside global)

ip nat inside source static 192.168.3.2 190.93.50.106

ip nat inside source static 192.168.3.3 190.93.50.107

ip nat inside source static 192.168.3.4 190.93.50.108

ip nat inside source static 192.168.3.5 190.93.50.109

to a specific port

ip nat inside source static tcp 192.168.3.2 80 190.93.50.106 80

ip nat inside source static tcp 192.168.3.3 80 190.93.50.107 80

ip nat inside source static tcp 192.168.3.4 80 190.93.50.108 80

ip nat inside source static tcp 192.168.3.5 80 190.93.50.109 80

res

Paul

Please don't forget to rate any posts that have been helpful.

Thanks.



kind regards
Paul

Please rate and mark posts accordingly if you have found any of the information provided useful.
It will hopefully assist others with similar issues in the future

View solution in original post

Highlighted
Beginner

Configuring NAT in multiples public server

So let me undertand this.

If I use the configuration that you gave me and I put a webservice (Example: FTP) in anyone of my internal IP address (Example 192.168.3.2), everybody that try to connect in a browser (outside - Internet)using 190.93.50.106 the router translate the petition a send to 192.168.3.2 (and viceversa)

Thanks for your help

Highlighted
VIP Mentor

Re: Configuring NAT in multiples public server

Hello
Yes that is correct

Res
Paul

Sent from Cisco Technical Support iPad App



kind regards
Paul

Please rate and mark posts accordingly if you have found any of the information provided useful.
It will hopefully assist others with similar issues in the future
CreatePlease to create content
Content for Community-Ad