cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1307
Views
0
Helpful
4
Replies

Configuring Port Channel on Cisco 2960S-48LPS-L

Tony Buoscio
Level 1
Level 1

When I try to move port channel connections to two of the SFP ports on our Cisco 2960S switch, one of the connections fail.

I am using two GBics, both are the same, GLC-T-A 1000Base-T.

 

The port channel work fine when I use g1/0/47 and 48.

The port channel work fine when using g1/0/48 and SFP 1/0/49

Port channel does not work when using SFP 1/0/49 and SFP 1/0/50.

 

 

 

4 Replies 4

Reza Sharifi
Hall of Fame
Hall of Fame

What is the error message you get?

When this happens, what does the log show?

What version of IOS are you running?

 

Cisco C2960S software version:  12.2(55)SE7.  Using C2960S-UNIVERSALK9-M.

Port configurations for g1/0/48 - 51:

interface GigabitEthernet1/0/49
 description Trunk to Cisco Core
 switchport mode trunk
 srr-queue bandwidth share 1 30 35 5
 priority-queue out
 mls qos trust cos
 macro description cisco-switch
 auto qos trust
 spanning-tree link-type point-to-point
 channel-group 2 mode on

When working, both ports show green status lights.

ort      Name               Status       Vlan       Duplex  Speed Type
Po2       Trunk to Core      connected    trunk      a-full a-1000
 *: interface is up
 IHQ: pkts in input hold queue     IQD: pkts dropped from input queue
 OHQ: pkts in output hold queue    OQD: pkts dropped from output queue
 RXBS: rx rate (bits/sec)          RXPS: rx rate (pkts/sec)
 TXBS: tx rate (bits/sec)          TXPS: tx rate (pkts/sec)
 TRTL: throttle count

  Interface               IHQ   IQD  OHQ   OQD  RXBS RXPS  TXBS TXPS TRTL
-------------------------------------------------------------------------
* Port-channel2            0     0    0     0 8390000  909 970000  551    0

Age of the Port-channel   = 0d:10h:57m:35s
Logical slot/port   = 5/2          Number of ports = 2
GC                  = 0x00000000      HotStandBy port = null
Port state          = Port-channel Ag-Inuse
Protocol            =    -
Port security       = Disabled

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits
------+------+------+------------------+-----------
  0     00     Gi1/0/47 On                 0
  0     00     Gi1/0/49 On                 0

 

When not working, one port shows green, then other port status light is off.

GigabitEthernet1/0/49 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is 3c0e.233f.a531 (bia 3c0e.233f.a531)
  Description: Trunk to Cisco Core
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:09, output 00:00:19, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 1954000 bits/sec, 213 packets/sec
  5 minute output rate 38000 bits/sec, 16 packets/sec
     2935639 packets input, 880524431 bytes, 0 no buffer
     Received 2211794 broadcasts (310067 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 310067 multicast, 0 pause input
     0 input packets with dribble condition detected
             370489 packets output, 66729219 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out


GigabitEthernet1/0/50 is down, line protocol is down (notconnect)
  Hardware is Gigabit Ethernet, address is 3c0e.233f.a532 (bia 3c0e.233f.a532)
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Auto-duplex, Auto-speed, link type is auto, media type is Not Present
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
 --More--              0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

Let me know if you need more info.

Tony, we need more details like Reza mentioned.

 

the Port config of both switches, the logs...I nerver faced that issue..

Hi Tony,

Please share more details. Is problem only with 1/0/50 not being able to add to bundle?

Please share config, log message etc to check

 

Thanks,

M