05-08-2013 09:31 PM - edited 03-07-2019 01:15 PM
Hi,
I have a problema with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous witrh single ssid on vlan 10.
When I connect the AP to sw1, I receive dhcp with no problems.
When I connect the AP to sw 2, I’m not getting IP by DHCP.
I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.
The trunk ports are also configured as trusted.
The port 1 of ws 1 that goes to the C800 is also configured as trusted.
I need some help to figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.
The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
thanks
05-09-2013 12:32 AM
Hello
Do you have connecrivity from this port?
Can you receive an ip address from dhcp if you plug a pc into it? - Have you tried static addressing ?
On switch 2 have you defined L2 vlan for vlan 10?
res
Paul
Sent from Cisco Technical Support Android App
05-09-2013 05:21 AM
Vlan 10 is configured as access on all ports, and is passing tru the tunk port.
If I’m connected tp the sw 2 with a wired, I get IP by DHCP without any problem and have full connectivity.
If I configure a static ip address on my wireless interface, I have full connectivity tru the SSID.
Thanks
05-09-2013 06:43 AM
Hello
Can you post the config of the wlan ap
res
Paul
Please don't forget to rate any posts that have been helpful.
Thanks.
05-09-2013 07:35 AM
!
! Last configuration change at 18:10:56 GMT Sun Feb 28 1993 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname AP
!
!
logging rate-limit console 9
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
!
!
!
!
aaa session-id common
clock timezone GMT -6 0
ip cef
!
!
!
ip dhcp-server 10.69.32.1
dot11 syslog
!
dot11 ssid xtndsyses
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 03227D2D202A04696B2D3D213330292E260B0A05096365
!
!
dot11 network-map
crypto pki token default removal timeout 0
!
!
username --- privilege 15 secret 5
username --- privilege 15 secret 5
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
!
encryption mode ciphers tkip
!
ssid xtndsyses
!
antenna gain 0
stbc
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
!
encryption mode ciphers tkip
!
ssid ssidap
!
antenna gain 0
dfs band 3 block
stbc
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
ip address 10.69.32.7 255.255.255.0
ip helper-address 10.69.32.1
!
ip default-gateway 10.69.32.1
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 10.69.32.1
!
snmp-server community ro RO
snmp-server community rw RW
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
transport input all
!
end
05-09-2013 08:54 AM
Hello,
Are you trying to obtain dhcp for clients connecting to this AP or for the AP to obtain a dynamic ip address?
Please don't forget to rate any posts that have been helpful.
Thanks.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: